Wood stains
Application Weather and water-resistant, open-pored protective and decorative coating for exterior wooden facades and walls. Technical properties Glazing to opaque depending on application thickness. Very weather-resistant and colour-fast, permeable to water vapour. Block-resistant, therefore suitable for windows and doors. Colour 712 silver grey, 713 silver anthracite. Ingredients Ricin oil - natural resin boiling, natural resin ester, wood oil - stand oil, kaolin, zinc oxide, alumina, micro wax, isoparaffins, silicic acid, natural asphalt, mineral pigments, iodo-2-propynyl-butylcarbamate, drying agents. Substrate and preparation The substrate must be dry, solid, clean, grease-free, dust-free and absorbent. A fungus-inhibiting primer, e.g. with LEINOS Impregnation Primer 150, should be applied in advance. How to apply Stir carefully before use. Brush, roll or spray. If necessary, the wood surfaces can be pre-sanded with 120 grit in the direction of the grain. The product can also be applied directly to rough sawn wood. We recommend priming with LEINOS Impregnation Primer 150, followed by 1-2 coats of Facade Stain 264. Allow each coat to dry thoroughly before continuing. Intermediate sanding is not necessary. To achieve optimum results, please observe the technical data sheets for all products used. The ambient and surface temperature during application should be above 12 °C. Drying time Approx. 16-24 hours. This system requires sufficient quantities of atmospheric oxygen for drying. Coverage Approx. 40-60 ml/m² per application, equivalent to 16-25 m² per litre. Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Stir thoroughly before use. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 400 g/l, EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: Ö60+ Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains 3-Iodo-2-propynyl-butylcarbamate. May produce an allergic reaction. Active ingredient: 3-Iodo-2-propynyl-butylcarbamate <0,6%. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For the coloured design of wooden ceiling and wall panelling, as well as wooden furniture parts in interior areas. Technical properties Glazing, water vapour permeable, easy to apply water-based glaze. Fast drying and polishable. Colour Wax Varnish is available both as a colourless version (can be tinted as desired with our pigment concentrates 668) and as a ready-to-use white glaze. Ingredients Water, carnauba wax, micro wax, methyl cellulose, soya lecithin, mineral pigments (except colourless), benzisothiazolinone. Substrate and preparation The substrate must be dry, solid, clean, free of grease and dust. Pre-sand wooden surfaces with 100-180 grit in the direction of the fibres, depending on the type of wood and the desired penetration depth. How to apply Stir carefully before use! Use a brush or paintbrush, sponge or cotton cloth. Room and surface temperature above 15 °C. For a coloured coating, the colourless wax glaze can be coloured up to 20% with LEINOS Pigment Concentrates. Depending on the quantity of pigments added and the number of coats, the strength of the colouring and the coverage can be increased. Drying time Dried after 1-2 hours, completely dry after approx. 24 hours. Coverage Approx. 80-100 ml/m² depending on the absorbency of the wood. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930. Storage and shelf life Stable for approx. 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost! Special notes Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Weatherproof and waterproof, open-pored protection for exterior use, with film protection against fungal attack. For absorbent wooden substrates: exterior windows and doors, fences, pergolas, roof overhangs, shingles, wooden panelling, wooden houses. Not suitable for children's toys due to the film preservative used. Technical properties Glazing, water-repellent coating. Water vapour permeable. Tested according to ihd and ift Rosenheim guidelines for discolouration by mortar, water vapour permeability, compatibility with sealing profiles, resistance to weathering. Tested for migration behaviour according to DIN EN 71, part 3. saliva and perspiration resistant according to DIN 53160. not suitable for floors. Colour 002 Colourless (without UV protection), 022 Pine, 042 Teak Dark, 056 Nordic Red, 062 Walnut, 072 Oak, 082 Rosewood, 102 Ebony, 123 Frisian Blue, 202 White (only for non-weathered surfaces), 212 Light Grey, 733 Anthracite Grey. See colour sample card Wood Varnish 260. Ingredients Wood oil, ricin oil, linseed oil, natural resin ester, isoparaffins, micro wax, zinc oxide, mineral pigments, iodopropynyl butyl carbamate, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, grease-free, dust-free and absorbent. How to apply Brush, roll or spray. Ambient and surface temperature above 15°C. A. Coating structure for untreated or absorbent substrates: Pre-sand wooden surfaces with 120 grit in the direction of the fibres. Prime with Impregnation Primer 150, then apply 3 thin coats of Wood Varnish 260. To achieve optimum results, please refer to the technical data sheets for all products used. B. Renovation coat: Completely remove old coats that close the pores. If the substrate is absorbent, it must be primed. Then apply 3 thin coats of Wood Varnish 260. Please note: Protect old cracked beams from driving rain during and 3 - 4 days after painting. Cracks in young wood that appear later must be treated immediately. Sprayability (non-binding guide values): Airless: Working pressure: 100-150 bar, nozzles 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes. High pressure: working pressure: 2.0-2.5 bar, nozzle 0.20 mm, low pressure: nozzle 0.20 mm. Drying time Approx. 16-24 hours in a normal climate. Coverage Approx. 60-80 ml/m² per application. Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 480 g/l, EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: Ö 60+ Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains 3-Iodo-2-propynyl-butylcarbamate. May produce an allergic reaction. Active ingredient: 3-Iodo-2-propynyl-butylcarbamate <0,6%. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Waterproof, open-pored protection for interior use. Without film protection against fungal attack, therefore only limited use outdoors. For absorbent wooden surfaces: windows and doors (interior), shelves, toys, beehives. Technical properties Glazing, water-repellent coating. Water vapour permeable. Tested according to ihd and ift Rosenheim guidelines for discolouration by mortar, water vapour permeability, compatibility with sealing profiles, resistance to weathering. Tested for migration behaviour according to DIN EN 71, part 3. saliva and perspiration resistant according to DIN 53160. not suitable for permanent, high water exposure. Colour 002 Colourless (without UV protection), 022 Pine, 042 Teak Dark, 056 Nordic Red, 062 Walnut, 072 Oak, 082 Rosewood, 102 Ebony, 123 Frisian Blue, 202 White (only for non-weathered surfaces), 212 Light Grey. Ingredients Wood oil, ricin oil, linseed oil, natural resin ester, isoparaffins, micro wax, zinc oxide, mineral pigments, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, grease-free, dust-free and absorbent. How to apply Brush, roll or spray. Ambient and surface temperature above 15 °C. A. Coating structure for untreated or absorbent substrates: Pre-sand wooden surfaces with 120 grit in the direction of the fibres. Prime with Primer Oil 220, then apply 2-3 thin coats of Wood Varnish 261. To achieve optimum results, please refer to the technical data sheets for all products used. B. Renovation coat: Completely remove old coats that close the pores. If the substrate is absorbent, it must be primed. Then apply 2-3 thin coats of Wood Varnish 261. Please note: Protect old cracked beams from driving rain during and 3-4 days after painting. Cracks in young wood that appear later must be treated immediately. Sprayability (non-binding guide values): Airless: Working pressure: 100-150 bar, nozzles 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes. High pressure: working pressure: 2.0-2.5 bar, nozzle 0.20 mm, low pressure: nozzle 0.20 mm. Drying time Approx. 16 - 24 hours. For reliable drying and to avoid odours, we always recommend using a fan to ensure sufficient air circulation on the surface of the paint during the drying phase. Coverage Approx. 60-80 ml/m² per application. Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 480 g/l, EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: Ö 60+ Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Water-based Wood Varnish for all types of interior and exterior wooden surfaces. Particularly suitable for softwoods but also for hardwoods and hardwoods for decorative colouring and protection against soiling and weathering. Not suitable for the final treatment of floors, stairs and other surfaces subject to particularly heavy wear. Technical properties Wood Varnish, water-based with vegetable oil-based binders, high quality for colouring and protective coating. The product penetrates deep into the wood and gives the surfaces a velvety, luminous, homogeneous colour while retaining the natural grain. Colour 002 colourless, 022 pine, 041 teak, 057 Swedish red, 062 walnut, 063 mahogany, 072 oak, 082 rosewood, 102 ebony, 202 white, 212 light grey, 403 dove blue, 731 anthracite. Ingredients Water, natural oil-based binder emulsions, carnauba wax, talc, drying agents, pigments, preservatives. Substrate and preparation Remove old coats completely, otherwise they may show through the glaze. For optimum adhesion, sand the wood with 150 grit. The substrate must be free of dirt and grease. The room and surface temperature should not be below 16 °C. How to apply Carefully remove any skin that may be present. Only then stir thoroughly and apply evenly in the direction of the fibres with a glaze brush or paint roller. The application quantity of the first coat depends on the absorbency of the substrate. Always work sparingly. A second coat can be applied after approx. 4-6 hours drying time in order to create a sufficient protective effect and achieve the desired colour tone. Ideally, the surfaces should be left to harden overnight before being exposed to loads. Wood Varnish, water-based can also be applied by spraying. To be on the safe side and to achieve the desired colour design, always carry out a preliminary test. Sprayability (non-binding guide values): Airless: Working pressure: 100-150 bar, nozzles 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes. High pressure: working pressure: 2.0-2.5 bar, nozzle 0.20 mm, low pressure: nozzle 0.20 mm. Drying time The first coat is usually dust-dry after approx. 2 hours, recoatable after 4-6 hours and completely dry after approx. 6-8 hours. The glaze is cured after approx. 2 days. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage Depending on the absorbency of the wood, 60-90 ml/m² is required for the first coat. This depends very much on whether the surfaces are rough-sawn or planed and/or have been sanded. Around 40-50 ml/m² is then required for the second coat. Thinner and cleaning agent Only with water. Recommended quantity 2-5 %. Thinner may cause the glaze to settle more quickly. A soap solution (e.g. washing-up liquid) is recommended if the tools need to be cleaned again due to oily residues on the brush or roller. Storage and shelf life The product has a shelf life of at least 1 year in the closed original container. Store in a cool and dry place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 30 g/litre. EU limit value: 130 g/l (cat. a). GISCODE: BSW20 / EAK: EAK 08 01 20 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)