Wood cleaning products
Application For treating all oiled and waxed surfaces such as wood, cork and linoleum in indoor areas, to prevent the formation of worn paths. Technical properties Transparent, easy to use. The open-pored, silk-matt, hard-wearing and water-repellent surface is resistant to yellowing. Tested for migration in accordance with DIN EN 71, Part 3. Sweat and saliva resistant in accordance with DIN 53160. Colour 002 Colourless Ingredients Linseed oil, wood oil, castor oil, natural resin esters, isoparaffins, zinc oxide, alumina, kaolin, talc, micro-wax, silica, drying agents. Substrate and preparation The substrate must be dry (wood moisture content max. 14 per cent) and free from dirt and grease. Clean using LEINOS Vegetable Soap 930 (wipe with a damp cloth). Rinse with clean water. Allow the floor to dry thoroughly. The floor temperature during application must be at least 16 °C. How to apply Stir thoroughly before use! Apply the Oil Refurbisher evenly and in a thin layer using a short-pile floor mop. After 15–20 minutes, remove any excess oil and polish the surface with a white pad. Heavily worn and faded, dry surfaces must be treated a second time with Oil Refurbisher. Heavily worn, stressed surfaces can also be treated with Hardwax Oil 290. Carry out a test application first! Ensure optimal fresh air circulation during application and drying! Oil wash: Depending on the degree of soiling and the absorbency of the wood, apply 100–200 ml/m² evenly. Then use a green pad to loosen the dirt and carefully wipe it away with a rubber squeegee or similar tool. Depending on the level of soiling, this soiled solution can be reused approximately 2–3 times on the adjacent area. Once the floor area of a room has been cleaned, rub it down completely once more with a white pad until no residue remains. To achieve a uniform surface finish, after a drying time of approx. 24 hours, Oil Refurbisher can be applied very thinly, drop by drop, using a white polishing pad. Carry out a test application first! Drying time Dry after 6–12 hours (20 °C, relative humidity 50–55 per cent); ready for sanding and recoating. Floors can be used with care after 1 day. Full use after 7–14 days. This system requires atmospheric oxygen to dry. Therefore, ensure good ventilation; if the air is stagnant, use a fan, for example (also to prevent odours from developing). Coverage Consumption and coverage depend on the absorbency of the surface and the intended use. Maintenance: approx. 30–40 ml/m². Oil cleaning: approx. 100–200 ml/m². Determine the exact consumption on site. Thinner and cleaning agent Immediately after use, clean with LEINOS Thinner 200. Storage and shelf life Store in a cool, dry place, away from frost. Seal the container tightly. Unopened, it will keep for at least 2 years. Remove any skin that may have formed before using again. Special notes Store work materials impregnated with the product, where the oil has not fully dried, in an airtight metal container or in water, and then dispose of them, as there is otherwise a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may cause a characteristic odour. When using spray equipment, wear approved respiratory protection. Wear a fine dust mask when sanding! Colour specifications and colour swatches are for guidance only. Colour variations are possible depending on the batch, substrate and printing technique. The dried original colour tone differs from the fresh colour tone in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour together. VOC content: 660 g/l. EU limit value: 700 g/l. (Cat. f). GISCODE: Ö 60+ / EAK: 08 01 11 Hazard statements Contains: Hydrocarbons, C10-C13, n-alkanes, iso-alkanes, cyclic, < 2% aromatics. May be fatal if swallowed and enters airways. Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Intensive cleaning agent for heavily soiled indoor and outdoor surfaces, e.g. wooden decking, fences, doors, stone tiles, masonry, etc. Ideal for cleaning and removing fungal and algae infestation. Highly concentrated. Technical properties Liquid consistency, very economical, strong cleaning effect. Made from purely plant-based, renewable raw materials. Ingredients Water, Vegetable Soap, Surfactants. How to apply Dilute Intensive Cleaner 1:20 to 1:40 with warm water, depending on the degree of soiling. E.G: mix 250 ml Intensive Cleaner with 5-10 litres of water. Apply the cleaner evenly with a wide brush or paintbrush. The treated surface should be sufficiently wet. Leave to work for approx. 20 minutes. Then scrub/wash the surface thoroughly with a brush. Repeat the treatment if necessary. Rinse the surface with water and leave to dry. Neutralise the surfaces thoroughly with water before further treatment with other products. Do not apply below +8 °C. Tip: In the case of heavy fungal and algae infestation, leave the Intensive Cleaner to work for 3-4 days, then rinse with water. Remove any remaining stains with a hard brush. Clean tools with water immediately after use. Coverage 1 litre of concentrate properly diluted with water is sufficient for approx. 120-150 m². Thinner and cleaning agent Clean with water immediately after use. Storage and shelf life Store in a cool, frost-free and dry place. Keep opened containers tightly closed. Special notes EAK: 07 06 01 / GISCODE: GE 10 Hazard statements Causes skin irritation. Causes serious eye irritation. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Water-based alkaline cleaning agent for removing oils and waxes from wood and metal surfaces. Not suitable for non-ferrous metals such as zinc and aluminium. Technical properties Mild alkaline cleaning agent with good surface wetting and dissolving power for oils and waxes. Ingredients Water, potash, non-ionic and amphoteric surfactants, glycerine, xanthan gum. How to apply Before cleaning, carry out a test on an inconspicuous area with LEINOS Oil and Wax Remover to check the effect on the surface material. Cover glass, ceramic, clinker and wooden surfaces that cannot be cleaned well. Apply a generous amount of undiluted LEINOS Oil and Wax Remover and work in with a pad. After a contact time of 5-10 minutes, wash the surface thoroughly with clear water. In the case of stubborn stains, further treatment with Oil and Wax Remover may be necessary. Discolouration may occur on woods containing tannic acid, e.g. oak. These can be removed by treatment with LEINOS Tannic acid Stain Remover 946. Coverage Consumption depends on the type and degree of soiling. Thinner and cleaning agent Water. Storage and shelf life Store in a cool and frost-free place. Shelf life is at least 24 months if unopened. Special notes EAK: 07 01 01 / GISCODE: GG40 Hazard statements Causes serious eye irritation. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Water-based cleaning agent for removing dark discolouration from oak wood. Not suitable for smoked oak. Technical properties Removes dark discolouration from wood containing tannic acid, such as oak. Has a brightening effect on older, darkened wood surfaces. Colour Colourless. Ingredients Water, oxalic acid, non-ionic surfactants, polyaspartic acid. How to apply Shake before use. At high temperatures, the wood should be moistened. Avoid direct sunlight as far as possible. Apply a thin layer of Tannic acid Stain Remover to the discoloured area. Leave to work for about 15 minutes. Then rinse the surface thoroughly with clean water. In the case of stubborn discolouration, further treatment with Tannic acid Stain Remover may be necessary. Once completely dry, the area can be treated with a care product, oil or wax. After removing stubborn discolouration, a light sanding may be necessary before refinishing. Coverage Consumption depends on the type and degree of soiling. Thinner and cleaning agent Water. Storage and shelf life Store in a cool and frost-free place. Shelf life is at least 24 months if unopened. Special notes GISCODE: GG10 / EAK: 07 06 01 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Water-based cleaning agent for removing stains from treated and untreated wood. Technical properties Solvent-free product. Good wetting of the surface of untreated, oiled or waxed wood. Penetrates into the pores. Stains, for example coffee, tea or red wine stains, are dissolved from the wood and washed away. Ingredients Water, non-ionic surfactants. How to apply Before cleaning, carry out a test with the stain remover on an inconspicuous area to check the effect on the surface material. Spray the stain remover undiluted onto the stain. After a reaction time of 15-30 minutes, gently work the stain with a brush or cloth until it has dissolved. For stubborn stains, further treatment with the stain remover may be necessary. Remove the washing solution with lukewarm water and dry the surface with a cloth. Once completely dry, the surface can be treated with a care product, oil or wax. Coverage Consumption depends on the type and degree of soiling. Storage and shelf life Store in a cool and frost-free place. Shelf life is at least 24 months if unopened. Special notes GISCODE: GG10 / EAK: 07 06 01 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application This moisturising universal cleaner is ideal for maintaining wooden floors and worktops. Applied undiluted, it dissolves even stubborn dirt. This natural product, a vegetable fatty acid soap based on old recipes, can be used universally as a powerful household cleaner. Technical properties Liquid consistency, very economical, strong cleaning effect, highly moisturising. Made from purely plant-based, renewable raw materials. Colour Colourless, transparent, slightly yellowish. Ingredients Water, potassium salts of fatty acids of vegetable oils. How to apply For oiled or waxed surfaces and untreated linoleum, work with a maximum Thinner of 30-50 ml per 10 litres of water to prevent the surface from becoming alkaline stained. For machine basic cleaning of oiled or waxed surfaces, dilute the soap 1:1 with water. Then rinse well. Coverage Application quantity approx. 30-50 ml per 10 litres of water. Thinner and cleaning agent Water. Product is ready to use, can also be used undiluted. Storage and shelf life Store in a cool and dry place. Storage stability approx. 2 years. Special notes GISCODE: GE 10 / EAK: 07 06 01 Hazard statements Causes skin irritation. Causes serious eye irritation. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For cleaning, care and finishing of soaped and leached, as well as natural and white oiled wood surfaces. For the initial treatment of softwood floors subject to normal wear, e.g. in living and sleeping areas, for wall and ceiling panelling, as well as for furniture and doors. Also suitable as an intensive cleaning agent for heavily soiled outdoor surfaces, e.g. wooden decking, fences, doors, stone tiles, brickwork, etc. Ideal for cleaning and removing fungal and algae infestation. Highly concentrated. Technical properties Liquid consistency, very economical, strong cleaning effect, highly moisturising. Made from purely plant-based, renewable raw materials. Colour 002 Colourless, 202 White Ingredients Water, potassium soaps of vegetable fatty acids, citric acid, xanthan gum, titanium dioxide (white). How to apply For intensive cleaning: Dilute Wooden Floor Soap 1:20 to 1:40 with warm water, depending on the degree of soiling. E.G: mix 250 ml Wooden Floor Soap with 5-10 litres of water. Apply the cleaner evenly with a wide brush or paintbrush. The treated surface should be sufficiently wet. Leave to work for approx. 20 minutes. Then scrub/wash the surface thoroughly with a brush. Repeat the treatment if necessary. Rinse the surface with water and leave to dry. The surface can then be treated with Terrace Wood Oil 236. Tip: In the case of heavy fungal and algae infestation, leave the Wooden Floor Soap to work for 3-4 days, then rinse with water. Remove any remaining stains with a hard brush. Clean tools with water immediately after use. Do not use at temperatures below +8 °C. Initial treatment of softwood floors: Add soap to the mop water (1:10), rinse a cotton cloth or mop in it, wring out slightly and damp mop the floor. Leave to act briefly and rinse the mop with clear water. Maintenance cleaning: Add soap to the mop water (1:40) and damp mop the floor as described above. Leave to work for a short time and rinse the mop with clean water, then remove stubborn dirt with a white pad and a little soapy water. Then wipe with a clean soap solution and leave to dry. Do not rinse with clean water! Coverage Intensive Cleaner: 1 litre of diluted concentrate (1:20 - 1:40) is sufficient for approx. 120-150 m². Initial treatment: 1 litre of diluted concentrate at a mixing ratio of 1:10 is sufficient for approx. 10-25 m². Underhelmet cleaning: At a mixing ratio of 1:40, 1 litre of concentrate is sufficient for 400-600 m². Storage and shelf life Store in a cool, frost-free and dry place. Keep opened containers tightly closed. Special notes EAK: 07 06 01 / GISCODE: GG10 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)