Wall paints
Application For white or coloured opaque, diffusion-open coatings on mineral substrates or firmly adhering wallpaper. Not suitable for damp rooms! Technical properties Highly opaque Casein Wall Paint in powder form for mixing with water. Water vapour permeable, reversible (can be removed again with water). Colour White, matt. Ready mixed, can be tinted with any LEINOS pigment concentrates 668. Ingredients Casein, chalk, marble flour, kaolin, diatomaceous earth, soda and methyl cellulose. No added preservatives or fragrances. Substrate and preparation Substrates that are not yet fully set, acidic or, above all, highly alkaline or highly absorbent must first be primed with LEINOS Deep Sealer 620 (water-based concentrate). The same applies to unstable substrates and sanding plasters. How to apply Brushing, rolling. Room and surface temperature above 15°C. A. Mixing: Stir 10 kg Casein Wall Paint 640 with approx. 7 litres of water until there are no more lumps. Then leave to swell for 30-60 minutes. Then add another 1 litre of water and stir well. It is best to work with a drill stirrer attachment. B. Tinting: Add the desired quantity of LEINOS Pigment Concentrate 668 and stir thoroughly. C. Application: The colour is best applied evenly with a roller or trowel. Avoid thick coats, rather apply two thin coats. Casein Wall Paint achieves its maximum opacity when dry. Due to its solubility in water, Casein Wall Paint is only suitable for the LEINOS glazing technique to a limited extent! Drying time Approx. 16-24 hours. Ensure good ventilation! Coverage Approx. 0.15 kg powder/m² per coat, may vary depending on the absorbency of the substrate. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930. Storage and shelf life Cool and dry. In powder form for many years. Consume immediately when mixed, as it contains no preservatives. Special notes VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Indoors. For all absorbent, mineral substrates, coatings in drywall construction, on fixed wallpaper and especially for clay substrates. Technical properties Solvent-free and water vapour permeable. Results in a matt surface and supports the moisture regulation of the living space. Coverage class 2, reversible. Colour Natural white, matt, can be individually tinted with LEINOS Pigment Concentrate 668. Ingredients Water, clay, chalk, titanium dioxide, starch ester polymer, cellulose, isothiazolinones. Substrate and preparation The substrate must be dry, solid, absorbent, clean and dust-free. If in doubt, carry out a test coat. Always stir well before use and during application. How to apply Always stir well before use and during application. Apply the paint evenly with a roller, brush or flat brush and spread in all directions. As a rule, 1 coat is sufficient. Ventilate well during application and drying time. Sprayability (non-binding guide values): Airless: Working pressure approx. 100 bar, nozzle approx. 0.43 mm. Low pressure: Nozzle for wall paints, maximum air volume, Thinner 5 % with water. Drying time At 23 °C and 50 % relative humidity approx. 6-12 hours. Coverage The consumption is approx. 150 ml/m². Storage and shelf life Store in a cool, dry and frost-free place. Shelf life is at least 1 year if unopened. Use up opened containers within 2 days. Special notes VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 19 / GISCODE: M-DF 01 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Indoors. For all absorbent, mineral substrates, e.g. lime plaster, cement plaster. Technical properties Solvent-free. Thanks to its particularly capillary properties and in conjunction with its high alkalinity (pH value approx. 13), Lime Paint 665 is antibacterial and ideal for use in mould prevention and remediation. Sd value approx. 0.01. Carbonates through the absorption of CO2 with mineral substrates. Results in a matt wall surface that can be painted over several times. Colour Natural white, matt, tintable with all lime-resistant LEINOS Pigment Concentrates 668, addition max. 20%. Ingredients Water, lime putty, chalk, marble powder, titanium oxide, cellulose ether, organic binder. Substrate and preparation The substrate must be dry, solid, absorbent, clean and free of efflorescence. Remove sintered skin from plaster surfaces mechanically. Pre-treat chalky and very absorbent surfaces with Mineral Plaster Primer 622. New base plasters must be at least 2-3 weeks old. Substrates with water-soluble, discolouring substances must first be tested for suitability. If in doubt, apply a test coat. How to apply Always stir well before use and during application. Ideally, the paint should be applied evenly with a brush or flat brush and spread in all directions. Pre-wet highly absorbent, old lime paint coats. Depending on the substrate, apply 2-3 coats. Thin all coats with up to 20 % water. Pre-wet subsequent coats if necessary. High room air temperatures increase the water requirement. Lime Paint only achieves its full opacity when dry. Sprayability: After appropriate Thinner and sieving of the thinned paint, LEINOS Lime Paint 665 can be applied with an appropriate airless spraying device (non-binding information). Nozzle: 0.025"-0.031", without gun filter, main filter Mesh#30, spray pressure: 150-180 bar, spray angle: 50° Drying time At 20 °C and 50 % relative humidity: approx. 6-12 hours. Subsequent coats after 24 hours drying time. Coverage 1 litre is sufficient for approx. 5-8 m² per coat. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930. product is NOT ready for use! Storage and shelf life Store in a cool but frost-free place. Can be stored for approx. 12 months if originally sealed. Special notes With their special properties, LEINOS lime paint products correspond to a very old paint tradition and are becoming increasingly popular, especially in the area of mould remediation, due to their high pH value. A slight cloud formation, glossy lime sinter layers and colour variations on the wall surface correspond to the typical appearance of a lime paint coating. This appearance is influenced by the substrate, temperature and humidity and is one of the natural properties of lime paint coatings. The ageing of lime paint coatings occurs through a continuous, very slow reduction in layer thickness and is referred to as chalking in the technical literature. This chalking is a typical property of the material and NOT a product defect. To achieve optimum results, the material must be stirred thoroughly before use, diluted with 20% water and sieved. This also removes dried colour particles from the bucket rim and lid. These are typical properties of the material and NOT a product defect. VOC content: 0 g/litre. EU limit value: 30 g/l (cat. a). EAK: 08 01 19 / GISCODE: BSW60 Hazard statements Causes skin irritation. Contains: Calcium hydroxide. Causes serious eye damage. May cause respiratory irritation. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF INHALED: Remove person to fresh air and keep comfortable for breathing. Use only outdoors or in a well-ventilated area. Avoid breathing spray mist. Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Indoors against mould, algae and fungal infestation. LEINOS Mould Protection Paint is ready-to-use, solvent-free, based on vegetable and mineral raw materials and open to diffusion. Technical properties Solvent-free. The effect is based on a crystallisation process. This means that the colour ingredients are no longer available to organisms (mould, algae, fungi, etc.) as a source of food. The colour has a dry covering power. Damp areas on the wall become transparent. Due to its mode of action, the paint is not resistant to washing. Colour White. Tinting with LEINOS pigment concentrates 668 possible. Ingredients Water, silicic acid, common salt, calcium sulphate, cellulose, starch, titanium dioxide and plant extracts. Substrate and preparation The substrate must be dry, free of dust and grease, stable and moderately absorbent, free of separating agents, cracks and efflorescence. Treat surface mould infestation beforehand with LEINOS Mould Exx 960. How to apply At room temperatures above 12 °C. With roller or brush. Stir the paint well before use. Before drying, the paint looks like a non-covering coat. 2 coats are required for a reliable effect. Important: Structural damage, sources of moisture etc. must be repaired. Full opacity is only visible after drying. Drying time At 23 °C and 50 % relative humidity. Dries after a few minutes - high humidity extends the drying time. 2. Coat after 2-3 hours. Coverage Depending on substrate and application technique. Guide value 1 litre is sufficient for approx. 6.5 m² per coat. Determine the exact value on the object. Thinner and cleaning agent The product is ready to use. Clean tools immediately after use with warm water and LEINOS Vegetable Soap 930. Storage and shelf life Store in a cool, dry and frost-free place. Shelf life is at least 1 year if unopened. Keep opened containers tightly closed. Special notes VOC content: 1.0 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 / GISCODE: M-DF 01 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For white or coloured opaque coatings on all mineral substrates or firmly adhering wallpaper. Technical properties High hiding power, easy to apply, very economical. Solvent-free, low yellowing. Water vapour permeable according to DIN/EN ISO 7783-2 class 1, wash resistant according to DIN/EN ISO 11998 and DIN EN 13300, class 3, opacity class 2, wet abrasion resistance class 3. Colour Natural white, matt. Can be tinted as desired with LEINOS pigment concentrates 668. Ingredients Water, chalk, titanium dioxide, vegetable emulsifier, polyaspartic acid, starch ester polymer, talc, kaolin, methyl cellulose, isothiazolinone. Substrate and preparation Stir carefully before use. The substrate must be dry, free of dust and grease, moderately absorbent but stable, free of separating agents, cracks, efflorescence and fungi. Prime the substrate with water-based LEINOS Deep Sealer 620 if necessary. If the substrate reacts strongly alkaline, it must be neutralised beforehand. To achieve optimum wash resistance in accordance with DIN EN ISO 11998 and DIN EN 13300, Class 3, the substrate must not be absorbent when applying the final coat. How to apply At room temperatures above 12 °C with roller, brush or airless device. A. Painting on plaster, concrete and woodchip wallpaper: Paint 1-2 coats depending on the absorbency of the substrate. B. Plasterboard, fabric wallpaper: Prime with LEINOS Deep Sealer 620 (water-based concentrate). Then paint 1-2 times. C. Solid old coatings: Thoroughly clean old emulsion paint coats. Remove all traces of distemper coats and rinse. Carry out a test coat! Remove all traces of old latex, oil and varnish paints. Then apply a coat of paint as described under point B, with primer if the substrate is highly absorbent. Sprayability (non-binding guide values): Airless: Working pressure approx. 100-120 bar, nozzles 0.38-0.43 mm, spray angle approx. 30°-40°, filter approx. 100-50 meshes. Low pressure: Nozzle for wall paints, maximum air volume, Thinner with 5 % water. Drying time At 20 °C and 50 % relative humidity approx. 16-24 hours. This system requires sufficient amounts of atmospheric oxygen, a dry substrate and a relative humidity that is not too high. Coverage Approx. 100-200 ml/m² per application, may vary depending on the absorbency of the substrate. Thinner and cleaning agent Can be diluted with water. Product is ready to use. Clean tools with water and add LEINOS Vegetable Soap 930. Storage and shelf life Stable for approx. 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost! Special notes VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 / GISCODE: M-DF 01 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For all load-bearing interior wall and ceiling surfaces, except paint and latex coatings. Technical properties Wet abrasion class 2, contrast ratio class 2, sd value approx. 0.01m, pH value approx. 11. Mould-preventive: The product reacts alkaline and through silicification processes. Therefore, the colour ingredients are not available to organisms (mould, algae, fungi etc.) as a food source. Colour White. Ingredients Water, clay, chalk, potassium water glass, mineral pigments, organic binders, cellulose, vegetable emulsifier, polyaspartic acid. Substrate and preparation Plaster substrates that have not yet been painted, as well as gypsum plaster and plasterboard walls, should first be pre-treated with LEINOS Silicate Primer 621. Pre-treatment with LEINOS Silicate Primer 621 is also recommended to equalise different absorbencies, e.g. filler and repair areas. If in doubt, apply a test coat. Please note that smooth substrates will become somewhat grainy as a result of this primer. How to apply Silicate Clay Paint is easy to apply with a brush or roller after careful stirring. If necessary, dilute the first coat with max. 10 % water. The final coat is painted/rolled on undiluted. Sprayability (non-binding guide values): After appropriate thinning and sieving of the paint, LEINOS Silicate Clay Paint 689 can be applied accordingly. Airless: Working pressure approx. 100 bar, nozzle 0.25 mm, without gun filters, 50° spray angle. Drying time At 20 °C and 50 % relative humidity: Dust-dry after approx. 3 hours in a normal climate and can be painted over with Silicate Clay Paint after approx. 4 hours. Silicate Clay Paint is fully cured after 24 hours and can be glazed with Silicate Primer 621 (diluted 1:3 to 1:5 with water) and the alkali-resistant Pigment Concentrates for colouring. Ensure good ventilation! Coverage 1 litre is sufficient for 5-8 m² per coat, depending on the absorbency of the substrate. The consumption is approx. 150 ml/m². Thinner and cleaning agent Product is ready to use. Clean with water and LEINOS Vegetable Soap 930. Storage and shelf life Stable for at least 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost. Opened containers and diluted preparation cannot be stored. Special notes All LEINOS Silicate Paint products are particularly suitable for historical buildings, but also for use in modern architecture. In contrast to conventional paints bound with synthetic resins, silicate paints do not form a paint film after drying, but a paint layer. The ageing of these silicate paints is characterised by a continuous, very slow reduction in coating thickness. In technical literature, this behaviour is referred to as "chalking". This chalking is a typical property of the material and NOT a product defect. To achieve optimum results, the material must be thoroughly stirred and sieved before use so that dried colour particles are removed from the edge of the bucket or lid. These are typical properties of the material and NOT a product defect VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Do not get in eyes, on skin, or on clothing. Caution! Product is alkaline! Protect eyes and skin against splashes. Splashes on glass, natural stone, aluminium, wood and paint should be washed off immediately with plenty of water. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Dispersion Silicate Paint for all load-bearing interior wall and ceiling surfaces, with the exception of lacquer and latex coatings. Technical properties Wet abrasion class 2, contrast ratio class 2, sd value approx. 0.01m, pH value approx. 11. Mould-preventive: The product reacts alkaline and through silicification processes. As a result, the colour ingredients are not available to organisms (mould, algae, fungi, etc.) as a source of food. Colour Natural white. Ingredients Water, potassium water glass, mineral pigments, organic binders. Substrate and preparation Plaster substrates that have not yet been painted, as well as gypsum plaster and plasterboard walls, should first be pre-treated with LEINOS Silicate Primer 621. Pre-treatment with LEINOS 621 Silicate Primer is also advisable for levelling different absorbencies, e.g. filler and repair areas. Substrates with water-soluble, discolouring ingredients must first be tested for suitability. If in doubt, apply a test coat. Please note that this primer will make smooth substrates somewhat grainy. How to apply The Silicate Paint can be easily applied by brush, roller or spraying after stirring. If necessary, dilute the first coat with max. 10 % water. Paint the final coat undiluted. After approx. 4 hours, the Silicate Paint can be recoated with Silicate Paint for a second coat. Sprayability (non-binding guide values): After appropriate Thinner and sieving of the paint, LEINOS Silicate Paint 690 can be applied accordingly. Airless: Working pressure approx. 100 bar, nozzle 0.25 mm, without gun filters, 50° spray angle. Drying time At 20 °C and 50 % relative humidity: Dust dry after approx. 3 hours and can be painted over with LEINOS Silicate Paint 690 after approx. 4 hours. The Silicate Paint is fully cured after 24 hours and can be glazed with LEINOS Silicate Primer 621 (diluted 1:3 to 1:5 with water) and the alkali-resistant LEINOS Pigment Concentrates 668 for colouring. Ensure good ventilation! Coverage 1 litre is sufficient for 5-8 m² per coat, depending on the absorbency of the substrate. The consumption is approx. 150 ml/m². Thinner and cleaning agent Product is ready to use. Clean with water and LEINOS Vegetable Soap 930. Storage and shelf life Stable for at least 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost. Opened containers and diluted preparation cannot be stored. Special notes All LEINOS Silicate Paint products are particularly suitable for historical buildings, but also for use in modern architecture. In contrast to conventional paints bound with synthetic resins, silicate paints do not form a paint film after drying, but a paint layer. The ageing of these silicate paints is characterised by a continuous, very slow reduction in coating thickness. In technical literature, this behaviour is referred to as "chalking". This chalking is a typical property of the material and NOT a product defect. To achieve optimum results, the material must be thoroughly stirred and sieved before use so that dried colour particles are removed from the edge of the bucket or lid. These are typical properties of the material and NOT a product defect. VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Do not get in eyes, on skin, or on clothing. Caution! Product is alkaline! Protect eyes and skin against splashes. Splashes on glass, natural stone, aluminium, wood and paint should be washed off immediately with plenty of water. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Adhesive and finishing coat for embedding LEINOS Coating Fleece 725 in accordance with VOB DIN 18363, as well as for creating high-quality surfaces. For all load-bearing interior wall and ceiling surfaces, with the exception of paint and latex coatings. Technical properties In combination with an embedded glass fibre fleece, fire protection class A2 (non-combustible) is achieved in accordance with DIN 4102. A correspondingly classified substrate is required. Contrast ratio class 2, sd value approx. 0.01m, pH value approx. 11. Mould-preventive: The product reacts alkaline and through silicification processes. As a result, the colour ingredients are not available to organisms (mould, algae, fungi, etc.) as a food source. Colour Natural white. Ingredients Water, potassium-water glass, mineral pigments, modified organic binders. Substrate and preparation All surfaces to be reinforced must be prepared professionally in accordance with VOB Part C DIN 18636 or the BFS data sheets. Carefully remove wallpaper and paste residues. Depending on the quality requirements, the substrate should be at least a good Q2 levelling compound. Substrates with water-soluble, discolouring substances must be checked for suitability beforehand. Alkali-sensitive substrates must be covered. Smooth and non-absorbent substrates must be primed with LEINOS Mineral Plaster Primer, substrates with varying degrees of absorbency with LEINOS Silicate Primer 621, diluted 1:1 to 1:3 with water. LEINOS Silicate-Hybrid Paint is ready to use as a fleece adhesive and should NOT be diluted as an adhesive. How to apply LEINOS Silicate-Hybrid Paint is applied generously to all load-bearing substrates by rolling, brushing or spraying. One coat is sufficient! While the paint film is still wet (approx. 350-450 ml/m²), a glass fibre fleece (approx. 35 g/m² and 270 µm) is laid dry, free of creases and bubbles, with an overlap of approx. 5 cm and pressed down with a featheredge trowel. A wavy double seam cut creates an "almost invisible" seam area. The final coat is now applied immediately, wet on wet, with LEINOS Silicate-Hybrid Paint and can be thinned with water up to 5 % if necessary. Particularly advantageous: On filigree ceilings and prefabricated concrete walls, there is no need for time-consuming levelling work. Sprayability (non-binding guide values): Airless: Working pressure 120-140 bar, nozzle approx. 0.43 to 0.58 mm, spray angle approx. 40°, gun filter white 50 mesh, without HD filter. Drying time At least 24 hours at 20 °C and 50 % relative humidity. Ensure good ventilation! Coverage 1 litre is sufficient for approx. 1.5 m², depending on the absorbency of the substrate. The exact consumption must be determined in advance on a sample surface. Thinner and cleaning agent Product is ready to use as a non-woven adhesive and can be thinned with 5% water in the final coat. Clean with water and LEINOS Vegetable Soap 930. Storage and shelf life Stable for at least 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost. Opened containers cannot be stored. Special notes All LEINOS Silicate Paint products are particularly suitable for historical buildings, but also for use in modern architecture. In contrast to conventional paints bound with synthetic resins, silicate paints do not form a paint film after drying, but a paint layer. The ageing of these silicate paints is characterised by a continuous, very slow reduction in coating thickness. In technical literature, this behaviour is referred to as "chalking". This chalking is a typical property of the material and NOT a product defect. To achieve optimum results, the material must be thoroughly stirred and sieved before use so that dried colour particles are removed from the edge of the bucket or lid. These are typical properties of the material and NOT a product defect VOC content: 1 g/l, EU limit value: 30 g/l (cat a). EAK: 08 01 20 / GISCODE: M-SK 01 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Do not get in eyes, on skin, or on clothing. Caution! Product is alkaline! Protect eyes and skin against splashes. Splashes on glass, natural stone, aluminium, wood and paint should be washed off immediately with plenty of water. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For white or coloured opaque, diffusion-open coatings on all mineral substrates or firmly adhering wallpaper. Technical properties Good hiding power, easy to apply, very economical. Solvent-free, low yellowing. Water vapour permeable according to DIN/EN ISO 7783-2 class 1, wash resistant according to DIN/EN ISO 11998 and DIN EN 13300, class 3. Colour Natural white, matt. Ingredients Water, chalk, titanium dioxide, vegetable emulsifier, polyaspartic acid, starch ester polymer, talc, kaolin, methyl cellulose, isothiazolinone. Substrate and preparation Stir carefully before use. If the substrate reacts strongly alkaline, it must be neutralised. Loose substrates and sanding plasters must be primed with LEINOS Deep Sealer 620. To achieve wash resistance in accordance with DIN EN ISO 11998 and DIN EN 13300, class 3, the substrate must not be absorbent when applying the final coat. How to apply A. Coating on plaster, concrete and woodchip wallpaper: Paint 1-2 coats depending on the absorbency of the substrate. Drying time approx. 16-24 hours. B. Plasterboard, fabric wallpaper: Prime with LEINOS Deep Sealer 620, water-based concentrate. Then paint 1-2 coats. Drying time approx. 16-24 hours. C. Solid old coatings: Thoroughly clean old emulsion paint coats. Remove all traces of distemper and rinse. Carry out a test coat! Remove all traces of old latex, oil and varnish paints. Then apply a coat of paint as described under point A, with primer if the substrate is highly absorbent. Sprayability (non-binding guide values): Airless: Working pressure approx. 100-120 bar, nozzles 0.38-0.43 mm, spray angle approx. 30°-40°, filter approx. 100-50 meshes. Low pressure: Nozzle for wall paints, maximum air volume, Thinner with 5 % water. Drying time At 20 °C and 50 % relative humidity: approx. 16-24 hours. This system requires sufficient quantities of atmospheric oxygen, a dry substrate and a relative humidity that is not too high. Therefore, only work on a dry substrate and ensure good ventilation; if necessary, use a fan for safe drying and to prevent the formation of odours. Coverage Approx. 150 ml/m² per application, may vary depending on the absorbency of the substrate. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930, product is ready to use. Storage and shelf life Stable for approx. 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost! Special notes VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 / GISCODE: M-DF 01 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)