Oil & wax
Application Impregnation and protection of kitchen worktops, furniture surfaces and children's toys made of wood. Due to the heavy use of liquids and their chemical substances, worktops require a high-performance oil that is specially tailored to the requirements of the kitchen and food sector. Technical properties Very good stain resistance to coffee, red wine, fruit juices, etc. Fulfils the requirements of DIN EN 71-3 children's toy surfaces. It penetrates well into the wood, is diffusible, antistatic, revitalises and deepens the natural structure and colouring of the treated wood. When used as intended, the product complies with Regulation (EC) No. 1935/2004 and the German Food, Commodities and Feed Code (LFGB). Colour Colourless. Ingredients Linseed oil, wood oil, ricin oil, natural resin ester, isoparaffins, carnauba wax, drying agents. Substrate and preparation The substrate must be dry (wood moisture content below 14 %), solid, absorbent, clean and free of resin and dust. Good final sanding with 240 grit. How to apply Please stir carefully before use! Apply with a brush, cloth, roller or sponge at an ambient and surface temperature above 15°C. After a penetration time of approx. 20-30 minutes, rub off or remove excess oil and polish the surface dry with a cloth or pad. A. Untreated, absorbent substrate: 1. After a penetration time of approx. 20-30 minutes, rub or remove excess oil to areas that are still absorbent and polish the surface dry with a cloth or pad. 2. Apply another thin coat the next day and apply as described above. If necessary, apply a 3rd coat depending on the absorbency of the substrate. Important: No oil layer must remain on the surface! B. Renovation coat: For maintenance and refreshing, re-oil the surface as described above. Sand grey surfaces that have already been attacked with fine sandpaper (240 grit) or a pad and re-oil. Re-oil heavily used surfaces monthly. Carry out a preliminary test! Drying time Dry and recoatable after 18-24 hours (18-22 °C / 50-55 % relative humidity). Complete drying takes approx. 7-10 days. For reliable drying and to avoid odours, we always recommend using a fan to ensure sufficient air circulation on the surface of the paint during the drying phase. Coverage 20-50 ml/m² depending on the absorbency of the substrate. Thinner and cleaning agent Countertop Oil 280 is ready to use. Clean tools immediately after use with LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Shelf life is at least 2 years if unopened. Close opened containers tightly. Decant leftovers into smaller containers. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 360 g/litre. EU limit value: 700 g/l (cat. f). GISCODE: BSL10 / EAK: 08 01 11 Hazard statements Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions If medical advice is needed, have product container or label at hand. Keep out of reach of children. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For treating wooden kitchen worktops, furniture surfaces and children’s toys. Technical properties An oil-wax mixture, solvent-free, which permanently enhances the wood and guarantees a durable surface. Impregnating, water-repellent, open-pored, vapour-permeable. Saliva- and sweat-resistant in accordance with DIN 53 160. Tested in accordance with DIN EN 71, Part 3. When used as intended, the product complies with Regulation (EC) No 1935/2004 and the German Food, Consumer Goods and Animal Feed Code (LFGB). Ingredients Linseed oil, wood oil, sunflower oil, safflower oil, walnut oil, fatty acid methyl esters, kaolin, clay, drying agents. How to apply The substrate must be dry (wood moisture content max. 14 per cent), solid, absorbent, clean, and free from resin and dust. Finish sanding well with 240-grit sandpaper. Stir thoroughly before use. Apply with a brush, sponge, lint-free cloth or roller, and spread thoroughly. Drying time The drying time depends on the environment. At 20–23 °C, the drying time is 12–24 hours, depending on the amount of oil applied. To ensure the paint dries properly and to prevent odours from developing, we always recommend using a fan to ensure adequate air circulation over the painted surface during the drying phase. Coverage Approx. 60–80 ml/m² per coat. Apply sparingly to prevent drying problems! Storage and shelf life Store in a cool, dry place. Unopened, it will keep for at least 2 years. Seal opened containers tightly and transfer any remaining product to smaller containers. Special notes Store work materials impregnated with the product, where the oil has not fully dried, in an airtight metal container or in water, and then dispose of them, as there is otherwise a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may cause a characteristic odour. When using spray equipment, wear approved respiratory protection. Wear a fine dust mask when sanding! VOC content: 10 g/l. EU limit value: 400 g/l (Cat. e). EAK: 08 01 12 / GISCODE: BSL10 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For open-pored impregnation of all absorbent interior surfaces such as wood, cork and unglazed clay tiles, especially in areas subject to heavy wear. The durability of the surface can be significantly increased with a final treatment with Hard Oil Special 245. Technical properties Water-repellent, deeply penetrating impregnation. Permeable to water vapour. Tested according to EN 71, part 3 and for saliva and perspiration fastness according to DIN 53160. Colour 002 Colourless, 022 Pine, 062 Walnut, 092 Chestnut, 101 Double White, 142 Amber, 202 White, 212 Grey, 307 Black. Light-coloured, absorbent substrates may dry slightly darker. Woods are stained to varying degrees depending on their growth. Ingredients Linseed oil, wood oil, ricin oil, natural resin esters, isoparaffins, mineral pigments (except colourless), drying agents. Substrate and preparation The substrate must be dry, solid, clean, free of grease and dust, and absorbent. Pre-sand wooden surfaces with 150-180 grit in the direction of the grain. How to apply Stir carefully before use! Brushing, rolling, spraying, dipping. Room and surface temperature above 15 °C. The product should be applied in at least two coats. This can be done wet-on-wet: The second coat can be applied after a waiting time of 20-30 minutes. Important note: Irrespective of the application, the excess oil must be carefully removed approx. 30 minutes after the last application. Sprayability: Non-binding guide values: Airless: nozzle 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes, high pressure: nozzle 0.20 mm, spray angle 30° filter 100-180 meshes, low pressure: nozzle 0.20 mm Drying time Dust-dry after approx. 10-12 hours. Can be walked on and recoated after approx. 16-24 hours. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage Approx. 60-80 ml/m², may vary depending on the absorbency of the substrate. Thinner and cleaning agent The Hard Oil is ready to use. Clean with LEINOS Thinner 200. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 440 g/litre. EU limit value: 700 g/l (cat. f). GISCODE: Ö 60+ / EAK: 08 01 11 Hazard statements Contains: Hydrocarbons, C10-C13, n-alkanes, iso-alkanes, cyclic, < 2% aromatics. May be fatal if swallowed and enters airways. Repeated exposure may cause skin dryness or cracking. Safety instructions If medical advice is needed, have product container or label at hand. Keep out of reach of children. Read carefully and follow all instructions. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Store locked up. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For universal use. For impregnating all absorbent interior surfaces (wood, cork, porous stone), especially in areas subject to heavy wear (e.g. floors, doors, worktops, etc.). The durability of the surface can be significantly increased with a final treatment with Hard Oil Special 245. Technical properties Water-repellent, open-pored impregnation. Good fullness. Low yellowing. Not suitable for damp areas. Colour Transparent, colourless to slightly yellowish. Light-coloured surfaces dry slightly darker. Ingredients Safflower oil stand oil, safflower oil, natural resin ester, isoparaffins, drying agents. Substrate and preparation The substrate must be dry, solid, absorbent, clean and free of resin and dust. Product is ready to use. Stir carefully before use! How to apply Brushing, rolling, spraying, dipping. Room and surface temperature above 15 °C. The product should be applied in at least two coats. This can be done wet-on-wet: The second coat can be applied after a waiting time of 20-30 minutes. Important note: Irrespective of the application, the excess oil must be carefully removed approx. 30 minutes after the last application. Sprayability: Non-binding guide values: Airless: nozzle 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes, high pressure: nozzle 0.20 mm, spray angle 30° filter 100-180 meshes, low pressure: nozzle 0.20 mm Drying time At 20 °C and 50 % relative humidity: Dust-dry after approx. 8 hours. Tread-resistant and suitable for further treatment after at least 16-20 hours. For reliable drying and to avoid odour formation, we always recommend using a fan to ensure sufficient air circulation on the surface of the paint during the drying phase. Coverage Approx. 50-70 ml per m², per coat. Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry place. Close opened containers tightly, decant leftovers into smaller containers. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 460 g/l, EU limit value: 700 g/l (cat. f). GISCODE: Ö 60+ / EAK: 08 01 02 Hazard statements Contains: Hydrocarbons, C10-C13, n-alkanes, iso-alkanes, cyclic, < 2% aromatics. May be fatal if swallowed and enters airways. Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Indoors. For open-pored impregnation of wood. Creates a hard-wearing surface. Technical properties Scratch-resistant, water-repellent impregnation. Water vapour permeable. Solvent-free. Tested for migration behaviour in accordance with DIN EN 71, Part 3. Colour Colourless to slightly yellowish. Ingredients Linseed oil, wood oil, ricin oil, sunflower oil, carnauba wax, clay, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, free of grease and dust and absorbent. Pre-sand wooden surfaces with 100-150 grit in the direction of the grain. How to apply Apply once with a thermopad or polishing machine or surface brush. Room and surface temperature above 15 °C. A. Coating build-up on untreated or absorbent substrates: For hot application: Deep impregnation with a single application. In the floor area, apply a thin coat of cold Hard Oil Solvent-free 248 with a flat brush. Then carefully work in hot with a Thermopad machine. For cold application: Apply Hard Oil Solvent-free 248 1-2 times with an intermediate drying time of 24 hours. In floor areas, apply the product thinly with a flat brush. Then work in carefully with a polishing machine and white pad. If necessary, apply a second coat after an intermediate drying time of 24 hours. Consumption here only 3-5 g/m². Apply Hard Oil LF 248 drop by drop and polish in with a white pad. In general: Before further treatment with a LEINOS wax product, it must be ensured that the primed substrate is well dried and no longer absorbent in order to avoid impoverishment of the subsequent films and thus inferior surfaces! B. Renovation coat: Clean and sand the substrate. Then apply Hard Oil Solvent-free 248 once. Waxed surfaces can be renovated with Hard Oil Solvent-free 248 if the wax has been completely removed beforehand. Drying time Dust-dry after 24 hours. Dry after 48 hours. In general: This system requires sufficient oxygen in the air for drying. Therefore, ensure good ventilation, e.g. with a fan in stagnant air, to avoid odours. Coverage Consumption per application: Surface brush 20-30 ml/m². Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: <10 g/l, EU limit value: 400 g/l (cat. e). GISCODE: Ö 10+ / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions If medical advice is needed, have product container or label at hand. Keep out of reach of children. Read carefully and follow all instructions. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For open-pored final coating of interior surfaces that have been pre-treated with LEINOS Hard Oil 240 or similar products, especially in areas subject to heavy wear and in demanding furniture construction. Technical properties Hard, very scratch-resistant, water-repellent top coat. Water vapour permeable. Tested for the performance properties of wood varnishes/stains for interior use in accordance with DIN 68861, tested for migration behaviour in accordance with DIN EN 71, Part 3 and for saliva and perspiration fastness in accordance with DIN 53160. Colour Colourless to slightly yellowish. Silky lustre without polish. Ingredients Linseed oil, linseed oil stand oil, ricin oil, wood oil, natural resin ester, isoparaffins, alumina, micro wax, drying agents. Substrate and preparation Untreated wood must be pretreated with Hard Oil 240 or a similar product. The substrate must be dry, solid, clean, free of grease and dust and absorbent. Pre-sand wooden surfaces with 150-180 grit in the direction of the fibres. How to apply Stir carefully before use! Brushing, rolling, spraying, dipping. Apply sparingly to avoid drying problems! Room and surface temperature above 15 °C. Polishes up well. Important note: Regardless of the application, carefully remove the excess oil approx. 30 minutes after the last application. Sprayability: Non-binding guide values: Airless: nozzle 0.20 mm, spray angle: approx. 30°-40°, filter approx. 100-180 meshes, high pressure: nozzle 0.20 mm, spray angle 30° filter 100-180 meshes, low pressure: nozzle 0.20 mm Drying time Dust-dry after approx. 10-12 hours at 20 °C and 50 % relative humidity. Can be walked on and recoated after approx. 16-24 hours. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage Approx. 10-30 ml/m², may vary depending on the absorbency of the substrate. Thinner and cleaning agent The product is ready to use. Clean with LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Shelf life is at least 2 years if unopened. Close opened containers tightly, decant leftovers into smaller containers. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 450 g/l, EU limit value: 700 g/l (cat. f). GISCODE: Ö 60+ / EAK: 08 01 11 Hazard statements Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For priming and finishing all absorbent substrates, such as wood and cork floors, terracotta, stoneware tiles, neutral screed floors, wood-based panels such as Sterling OSB boards, etc., indoors. Technical properties Revitalises the natural structure, deepens the tone of the treated substrates and produces an open-pored, silky matt, hard-wearing and water-repellent surface that is largely resistant to yellowing. Tested for chemical resistance for interior use in accordance with DIN 68861 (e.g. water, coffee, beer, cola, red wine). Tested for migration behaviour in accordance with DIN EN 71, Part 3 and for saliva and perspiration fastness in accordance with DIN 53160. Colour 002 Colourless, 032 Colourless glossy (also suitable for cork surfaces), 053 Cherry, 054 Sand yellow, 062 Walnut, 076 Natural oak, 101 Double white, 102 Ebony, 200 Neutralising, 202 White, 212 Grey. Ingredients Linseed oil, wood oil, ricin oil, natural resin ester, clay, kaolin, zinc oxide, micro wax, silicic acid, isoparaffins, mineral pigments, drying agents. Substrate and preparation The substrate must be dry (wood moisture content max. 14 %), clean and dust-free. The application temperature should preferably not be below 16 °C. Drying behaviour is delayed at lower temperatures. Final sanding of the surfaces with at least 120 grit or grid. Particularly highly absorbent substrates, such as cork, must be primed with Hard Oil 240. How to apply Shake carefully before use. The Hardwax Oil is ready to use. Apply thinly and evenly with a short pile sealing roller or mop and spread well. Remove any excess after approx. 15-20 minutes and pad in with a green pad. After 16-24 hours, apply a second thin coat and polish with a white pad. If the surface feels rough after the first coat, sand with 150-180 grit. Remove sanding dust thoroughly before applying the second coat. A third coat of Hardwax Oil may be necessary for cork. Carry out a preliminary test! Ensure optimum fresh air circulation during application and drying of the products! Maintenance and aftercare: Clean floors treated with Hardwax Oil with Vegetable Soap 930 (add max. 10-30 ml to 10 litres of mopping water, use damp, not wet) and if necessary (if signs of wear appear) treat with Maintenance Oil 285. Heavily used surfaces (schools, offices, etc.) receive an initial basic treatment with Hardwax Oil 285 4 weeks after the last application of Hardwax Oil, after the floor has been cleaned with Vegetable Soap 930. Further maintenance care with Oil Refurbisher is carried out as required. Drying time The drying time is approx. 6-12 hours (20 °C / 50-55 % relative humidity). The 2nd coat is applied after 16-24 hours. Slightly loadable after 3 days. Full load-bearing capacity after 7-14 days. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage 30-50 ml/m²; coverage approx. 25 m²/litre. Determine exact consumption on the object. Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Shelf life is at least 2 years if unopened. Close container tightly. Remove any skin that may have formed before reuse. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 440 g/l, EU limit value: 500 g/l (cat. i). GISCODE: Ö 60+ / EAK: 08 01 11 Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For priming and finishing all absorbent substrates, such as wood and cork floors, terracotta, stoneware tiles, neutral screed floors, wood-based panels such as Sterling OSB boards, etc., indoors. Technical properties Hardwax Oil LF is an oil-wax mixture, solvent-free. It gives the wood a durable finish and guarantees a hard-wearing surface. It revitalises the wood structure and gives it a velvety sheen. Tested for migration behaviour in accordance with DIN EN 71, Part 3 and tested for saliva and perspiration fastness in accordance with DIN 53160. Colour 002 Colourless, 202 White. Ingredients Wood oil, linseed oil, ricin oil, sunflower oil, clay, kaolin, micro wax, mineral pigments (except colourless), drying agents. Substrate and preparation The substrate must be dry (wood moisture content max. 14 %), clean and dust-free. The application temperature should preferably not be below 16 °C. Drying behaviour is delayed at lower temperatures. Final sanding of the surfaces with at least 120 grit or grid. How to apply Apply Hardwax Oil LF evenly once with a double-sided trowel (approx. 15-30 ml/m², depending on the absorbency of the wood). Then pad thoroughly with a single disc polishing machine and green pad and polish the surface with a white pad. After 12 hours, apply a second thin coat of Hardwax Oil Colourless LF 291 or Hardwax Oil Colourless 290. For heavily used or particularly absorbent floors, apply a second coat sparingly the next day. Pad the surface with a white pad after 20-30 minutes. Ensure optimum fresh air circulation when applying and drying the products! Otherwise unpleasant odours are possible! Avoid layer formation at all costs! Please note: Floors must be laid without joints or levelled if necessary. If joints are present, oil may leak or noise may be generated when walking on the floor. Drying time The drying time is approx. 6-12 hours (20-23 °C / 50-55 % relative humidity). Complete drying and full load-bearing capacity after 7-10 days. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage 15-30 ml/m²; coverage: approx. 30-60 m²/l depending on the substrate. Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Close container tightly. Stable for at least 2 years when originally sealed. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 1 g/l, EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: Ö 10+ Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For a one-off, open-pored treatment of untreated or absorbent wooden surfaces in indoor areas that are subject to minimal mechanical stress. Not suitable for use in areas exposed to splash water. Technical properties Easy to apply. Once dry, it can be polished to a satin finish. Allows water vapour to pass through. Ingredients Linseed oil, sunflower oil, wood oil, natural resin esters, isoparaffins, carnauba wax, beeswax, bentonite, drying agents. Substrate and preparation Shake or stir thoroughly before use! The substrate must be dry, sound, clean, free from grease and dust, and absorbent. Pre-sand wooden surfaces with 100–180 grit sandpaper in the direction of the grain, depending on the type of wood and the desired depth of penetration. How to apply Apply with a brush or by dipping. Polish again once dry. Room and surface temperature must be above 15 °C. Shake or stir thoroughly before use! Drying time Approx. 18–24 hours. To ensure the paint dries properly and to prevent odours from developing, we always recommend using a fan to ensure adequate air circulation over the painted surface during the drying phase. Coverage Approx. 90 ml/m²; this may vary depending on the absorbency of the substrate. Thinner and cleaning agent LEINOS Thinner 200. The product is ready for use. Storage and shelf life Stable for at least 2 years when kept in the original, unopened container. Store in a cool, dry place, keeping the container sealed. Special notes Store work materials impregnated with the product, where the oil has not fully dried, in an airtight metal container or in water, and then dispose of them, as there is otherwise a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may cause a characteristic odour. When using spray equipment, wear approved respiratory protection. Wear a fine dust mask when sanding! VOC content: 450 g/l, EU limit value: 700 g/l (Cat. f). EAK: 08 01 11 / GISCODE: BSL40 Hazard statements Wiederholter Kontakt kann zu spröder oder rissiger Haut führen. Sicherheitsdatenblatt auf Anfrage erhältlich. Safety instructions st ärztlicher Rat erforderlich, Verpackung oder Kennzeichnungsetikett bereithalten. Darf nicht in die Hände von Kindern gelangen. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For one-time application on all interior wood. Not suitable for kitchen worktops, stairs and floors. Technical properties Solvent-free, impregnating, layer-forming. Elastic, antistatic. Welding and saliva resistant according to DIN 53 160. Colour Colourless, transparent. Ingredients Safflower oil, sunflower oil, linseed oil, wood oil, ricin oil, natural resin ester, beeswax, carnauba wax, micro wax, drying agents. Substrate and preparation The substrate must be dry, firm, clean and free of grease and dust. Shake well before use. How to apply Apply cold or hot with a brush, at room air temperatures above 15 °C. Allow to soak in, polish in with a pad after a contact time of 1-24 hours. Intermediate drying is not possible as there is no surface dryer. Drying time At 23 °C and 50 % relative humidity 24 hours. The supply of warm air considerably shortens the drying time. Coverage 1. Apply 10-15 ml/m², considerably less or more depending on the absorbency and surface condition of the substrate. Stir well. Carry out a test coat! Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 1 g/l, EU limit value: 400 g/l (cat. e). GISCODE: BSL10 / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For impregnating and maintaining all absorbent tiles and chemically neutral concrete surfaces, such as terracotta, indoors and outdoors. Technical properties Protects against general soiling, grease and oil. Suitable as joint protection for cement joints. Water-repellent and abrasion-resistant, does not noticeably stain the surface. Colour Colourless. Ingredients Wood oil, linseed oil, ricin oil, sunflower oil, natural resin esters, isoparaffins, drying agents. How to apply Stir carefully before use. Use a brush, cloth, roller or sponge. The surface must be dry, clean and free of grease and dust. Apply the stone oil with a brush or roller. After a penetration time of approx. 20-30 minutes, remove any excess oil from areas that are still absorbent and polish the surface dry with a cloth or pad. Apply another thin coat the next day and apply as described above. If necessary, apply a 3rd coat depending on the absorbency of the substrate. Important: No oil layer must remain on the surface! Drying time Dry and recoatable after 4-6 hours (18-22 °C / 50-55 % relative humidity). Complete drying takes approx. 7-10 days. For reliable drying and to avoid odour formation, we always recommend using a fan to ensure sufficient air circulation on the surface of the paint during the drying phase. Coverage 20-50 ml/m² depending on the absorbency of the substrate. Thinner and cleaning agent Product is ready to use. Clean the tools with LEINOS Thinner 200. Storage and shelf life Store in a cool and tightly closed place. If a skin forms, remove it before reuse. Sieve the oil if necessary. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 420 g/l, EU limit value: 700 g/l (Cat: f). Giscode: Ö 60+ / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Teak Oil is a high-quality oil resin treatment for all outdoor wood, such as fences, pergolas, children's play equipment, wooden decking, teak and garden furniture, etc. Very suitable for tropical woods such as Bangkirai. High-quality vegetable oils impregnate new wood and revitalise old wood. Technical properties Quick and easy application. The natural oils penetrate deep into the wood. They keep it healthy and elastic and prevent it from drying out. Good refresher for wood that has already been oiled. No sanding required for recoating. No unpleasant odours. Resistant to saliva and perspiration in accordance with DIN 53 160. Colour Colourless to slightly yellowish. Light-coloured, absorbent substrates dry slightly darker. Woods are stained to varying degrees depending on their growth. Ingredients Linseed oil, ricin oil, wood oil, isoparaffins, iodopropynyl butyl carbamate, drying agents. Substrate and preparation The substrate must be dry, solid, clean, free of grease and dust and absorbent. Completely remove old coats of varnish and opaque paint. Wood that has already turned grey should be sanded down to sound wood or pre-treated with LEINOS Anti-Greying Fluid 940. Allow pressure-impregnated wood to weather for one to two months and remove any salt efflorescence. How to apply Coating. Do not apply at temperatures below 10 °C and stir well before use. Apply thinly and evenly. Avoid the formation of puddles. Drying time At 20 °C and medium humidity dry after 6-8 hours, recoatable after 16-24 hours. Coverage Approx. 50 - 70 ml/m², may vary depending on the absorbency of the substrate. Thinner and cleaning agent Product is ready to use. Thinning and cleaning of tools with LEINOS Thinner 200. Storage and shelf life Store in a cool place. Shelf life is at least 2 years if unopened. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 420 g/litre. EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: BSL40 Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains 3-Iodo-2-propynyl-butylcarbamate. May produce an allergic reaction. Active ingredient: 3-Iodo-2-propynyl-butylcarbamate <0,6%. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Terrace Wood Oil is a high-quality oil resin treatment for all outdoor wood, such as fences, pergolas, children's play equipment, wooden decking, teak and garden furniture, etc. Also very suitable for tropical woods such as Bangkirai. High-quality vegetable oils impregnate new wood and revitalise old wood. Reddish: E.g. for bangkirai, larch and Douglas fir. Brownish: E.g. for oak, robinia, thermowood and all softwoods. Colourless for all exterior woods (without UV protection). Technical properties Quick and easy application. The natural oils penetrate deep into the wood. They keep it healthy and elastic and prevent it from drying out. Good refresher for wood that has already been oiled. No sanding required for recoating. No unpleasant odours. Resistant to saliva and perspiration in accordance with DIN 53160. Colour 002 Colourless (without UV protection), 015 brownish (e.g. for oak, robinia, thermowood and all softwoods), 052 reddish (e.g. for bangkirai, larch and Douglas fir) Ingredients Linseed oil, wood oil, ricin oil, isoparaffins, alumina, mineral pigments, iodopropynyl butyl carbamate, drying agents. Substrate and preparation The substrate must be dry, solid, clean, free of grease and dust and absorbent. Completely remove old coats of varnish and opaque paint. Wood that has already turned grey should be sanded down to sound wood or pre-treated with LEINOS Anti-Greying Fluid 940. Allow pressure-impregnated wood to weather for one to two months and remove any salt efflorescence. How to apply Coating. Do not apply at temperatures below 10 °C and stir well before use. Apply thinly and evenly. Avoid the formation of puddles. Drying time At 20 °C and medium humidity dry after 6-8 hours, recoatable after 16-24 hours. Coverage Consumption: 50-70 ml/m²; may vary depending on the absorbency of the substrate. Coverage: Approx. 13-23 m²/litre. Determine exact consumption on the object. Thinner and cleaning agent Terrace Wood Oil is ready to use. Thinning and cleaning of tools with LEINOS Thinner 200. Storage and shelf life Store in a cool place. Shelf life is at least 2 years if unopened. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 450 g/litre. EU limit value: 700 g/l (cat. f). GISCODE: Ö 60+ / EAK: 08 01 11 Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains 3-Iodo-2-propynyl-butylcarbamate. May produce an allergic reaction. Active ingredient: 3-Iodo-2-propynyl-butylcarbamate <0,6%. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Thinner for all oily products and for cleaning tools. Also suitable as a stain remover. Technical properties Colourless, mild. Low surface tension for good penetration and wetting. Ingredients Isoparaffins. How to apply If necessary, only add the Thinner in portions and stir carefully. Remove stains from oily products immediately with a cloth soaked in Thinner. This will save you solvent: - Clean brushes etc. in a suitably sized bucket with a lid. - Allow pigments and paint residues to sink to the bottom. - Pour the excess clear Thinner into a second bucket and leave the pigment and colour residue in the first bucket. - Pigment and colour residues can be disposed of in accordance with the applicable regulations. - The poured-off Thinner can be used again and again. Simply top up with new Thinner from time to time. - Close the bucket tightly after use and place it in a safe place. Coverage Depending on the application. Storage and shelf life Almost unlimited stability. Store in a cool, dry and sealed place. Special notes GISCODE: M-VM01 / EAK: 07 07 04 Hazard statements Contains: Hydrocarbons, C10-C13, n-alkanes, iso-alkanes, cyclic, < 2% aromatics. May be fatal if swallowed and enters airways. Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)