Paints & varnishes
Application Top coat for the decorative finish or renovation coating of wood, metal or stoneware surfaces in interior and exterior areas. Suitable for dimensionally stable wooden components such as windows and doors, limited dimensionally stable wooden components such as garden sheds, roof soffits, exterior gates and non-dimensionally stable wooden components such as fences, carports and palisades. Finishing Lacquer can be used for radiators as well as floor surfaces such as wooden stairs or floors. Cannot be used on anodised aluminium and galvanised surfaces. Technical properties High weather and light resistance, low yellowing, high opacity, good edge coverage, block-resistant, free of biocides and aromatic compounds. The product is easy to apply and produces a silky gloss surface. Colour White (127), black (913), anthracite grey (733), light grey (719), fir green (612), dove blue (403), Nordic red (356), yellow (221), blue (508), leaf green (614). All colours can be mixed with each other. Ingredients Binder based on vegetable oil, aliphatic hydrocarbons, titanium dioxide (depending on colour shade), inorganic/organic pigments (depending on colour shade), mineral fillers, additives, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, free of grease and dust and must not be absorbent. We recommend priming with LEINOS Resin Lacquer Primer 810 and intermediate sanding with 150/180 grit. For highly absorbent surfaces, a triple coat of LEINOS Primer Oil 220, Resin Lacquer Primer 810 and top coat may be advisable. For coloured coats, the Resin Lacquer Primer can be mixed with Finishing Lacquer in a ratio of 10:1. How to apply Product is ready for use. Stir carefully before use! Apply by brushing, rolling or spraying. Check compatibility and adhesion with the substrate by creating test areas. Protect surfaces from rain, wind, sunlight and condensation during application/drying. Intermediate sanding with at least 180 grit should be carried out between applications. Sprayability (non-binding guide values): Airless: Working pressure 120 - 160 bar, fine surfaces (cabinets, mouldings, furniture): Nozzle 0.28 - 0.33 mm, General painting work (doors, walls, ceilings): Nozzle 0.33 - 0.38 mm, gun filter 200 mesh. High pressure: Working pressure 2.0 - 2.5 bar, nozzle approx. 0.28 - 0.33 mm. Low pressure: Working pressure 0.2 - 0.8 bar, nozzle size: for paint colours 1.6 - 1.8 mm. Drying time Dust-dry after approx. 8 hours, touch-dry after approx. 12 hours. Can be sanded and painted over after 24 hours. This system requires sufficient quantities of atmospheric oxygen for drying. Therefore, ensure good ventilation. At low temperatures, high humidity or if the maximum layer thickness is exceeded, drying may be significantly delayed. For reliable drying and to avoid odours, we always recommend using a fan to ensure sufficient air circulation on the surface of the coating during the drying phase. Coverage Approx. 70-100 ml/m² depending on the absorbency of the substrate. Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains cobalt octoate. May cause allergic reactions. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Insulating coating against watery penetrating substrates indoors. Very well suited as a substrate for commercially available wool and fibre plasters. Technical properties Priming paint with good sealing effect. It produces a fine-grained, rough surface. This must be taken into account if Insulating Primer 815 is to be painted over with other LEINOS products. Colour Natural white. Ingredients Linseed oil, wood oil, ricin oil, natural resin ester, isoparaffins, talcum, chalk, titanium dioxide, alumina, drying agents. How to apply The substrate must be dry, clean, solid and free of dust and grease. Brushing, rolling (use a short-pile roller). Room and surface temperature above 15 °C. Paint low to normally absorbent plaster, concrete, cement, chipboard, gypsum fibreboard, metal and polystyrene boards with one full coat. Paint highly absorbent plaster, gypsum plasterboard, insulating fibreboard etc. twice. Check adhesion on non-absorbent substrates. Drying time At 20 °C/50-55 % relative humidity: Dust-dry after 8-10 hours, can be painted over with Insulating Primer after approx. 24 hours. Can be recoated with wool plaster after approx. 48-72 hours. For two coats with Insulating Primer after 4 days at the earliest. Ensure good ventilation! Coverage Do not exceed 100 ml/m² per coat. Thinner and cleaning agent Product is ready to use. Cleaning of tools: With LEINOS Thinner 200. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 150 g/l, EU limit value: 400 g/l (cat. e). EAK: 08 01 02 / GISCODE: BSL10 Hazard statements Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Open-pored, biocide-free primer for wood and metal indoors and outdoors. Also suitable for wooden floors & stairs (indoors only). Technical properties Waterproof, elastic, good filling and covering properties, good drying and sanding properties. Permeable to water vapour. Colour Natural white, matt. Ingredients Binder based on vegetable oil, isoparaffins, titanium dioxide, chalk, talcum, drying agents. Substrate and preparation The product is ready for application. The substrate must be dry, solid, clean, free of grease and dust and only slightly absorbent. How to apply Stir carefully before use! Brushing, rolling, spraying. Ambient and surface temperature above 15 °C. Check compatibility and adhesion with the substrate by creating test areas. Protect surfaces from rain, wind, sunlight and condensation during application/drying. For highly absorbent substrates, e.g. rough sawn wood, open-pored wood, we recommend priming with LEINOS Primer Primer, an intermediate coat of LEINOS Resin Lacquer Primer and a final coat of LEINOS Finishing Lacquer. Only apply an intermediate coat of LEINOS Resin Lacquer Primer if the primer coat was applied with LEINOS Primer Oil / Impregnation Primer. If the primer was applied with LEINOS Resin Lacquer Primer, omit the intermediate coat and start with the top coat. A. Coating structure for untreated or absorbent substrates: Stir before use. apply 1 sparing coat of LEINOS Resin Lacquer Primer 810 at temperatures above 15 °C. Then continue with LEINOS White Lacquer 820, Finishing Lacquer 840 and Finishing Lacquer Mix 845. B. Renovation on existing old coating: Completely remove old coatings that are not intact. Then apply a coat of paint as described under A. After sanding well and testing for compatibility, apply LEINOS White Lacquer 820, Finishing Lacquer 840 and Finishing Lacquer Mix 845 immediately. Sprayability (non-binding guide values): Airless: Working pressure 120 - 160 bar, fine surfaces (cabinets, mouldings, furniture): Nozzle 0.28 - 0.33 mm, General painting work (doors, walls, ceilings): Nozzle 0.33 - 0.38 mm, gun filter 200 mesh. High pressure: Working pressure 2.0 - 2.5 bar, nozzle approx. 0.28 - 0.33 mm. Low pressure: Working pressure 0.2 - 0.8 bar, nozzle size: for paint colours 1.6 - 1.8 mm. Drying time Dust-dry after approx. 3 hours. Dry, sandable and recoatable after 24 hours. This system requires sufficient quantities of atmospheric oxygen for drying. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage Approx. 60-80 ml/m² per coat. Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Clean tools with Thinner immediately after use. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Carefully remove any skin formation in the can before processing and do not stir in. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications/imprints are non-binding. A test coat with colour matching is therefore essential. VOC content: 350 g/l, EU limit value: 350 g/l (cat. g). GISCODE: BSL10 / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Protection and colouring for all open-pored screed and concrete surfaces, especially for basement stairs and garage floors. Not suitable for treating sealed old surfaces or glazed tiles. Technical properties Protects against general soiling, grease and oil. Suitable as joint protection for cement joints. Water-repellent and abrasion-resistant. Colour 130 Beige, 715 Cement grey, 732 Anthracite grey. Ingredients Rizine oil-natural resin ester boiling, natural resin ester, mineral fillers, natural asphalt, isoparaffins, drying agents. Substrate and preparation The substrate must be dry, clean, free of grease and dust and chemically neutral. Stir very thoroughly before use! How to apply Apply as thinly as possible with a brush, cloth, roller or sponge, spread or remove any excess after 15-20 minutes. Allow to dry well and apply a second coat without intermediate sanding. Spread this coat well and, if necessary, spread or remove excess material again. Depending on the absorbency of the substrate, a third or even fourth coat may be necessary. The surface must look well sealed without a noticeable layer having formed. Carry out a preliminary test! Important: Ensure optimum fresh air circulation during application and drying of the products! Drying time Dry and recoatable after 6-12 hours (18-22 °C/50-55 % relative humidity). Complete drying takes approx. 7-10 days. This system requires sufficient quantities of atmospheric oxygen for drying. For reliable drying and to avoid odour formation, we always recommend using a fan to ensure sufficient air circulation on the surface of the coating during the drying phase. Coverage 20-50 ml/m² depending on the absorbency of the substrate for the first coat. Subsequent coats approx. 20-25 ml/m². Thinner and cleaning agent Screed Paint 840 is ready to use. Clean tools immediately after use with LEINOS Thinner 200. Storage and shelf life Store in a cool and tightly closed place. If a skin forms, remove it before reuse. Sieve the oil colour if necessary. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 310 g/l, EU limit value: 400 g/l (cat. e). EAK: 08 01 11 Hazard statements Repeated exposure may cause skin dryness or cracking. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Open-pored top coat for all exterior wood constructions. Well suited for rough sawn wood. Not for window rebates, seating surfaces and floors or horizontal surfaces in weathered outdoor areas! Technical properties Good hiding power. Provides an elastic coating film. Weather and UV resistant. Water vapour permeable, with film protection against fungal attack. Resistant to saliva and perspiration according to DIN 53 160. Colour 014 Corn yellow, 057 Swedish red, 064 Earth brown, 104 Vine black, 123 Frisian blue, 204 Old white, 400 Fir green, 401 Steel grey, 733 Anthracite grey. All colours can be mixed with each other. Ingredients Linseed oil, wood oil, ricin oil, natural resin ester, isoparaffins, kaolin, chalk, silicic acid, clay, micro wax, mineral pigments, zinc oxide, iodopropynyl butyl carbamate, drying agents. Substrate and preparation The substrate must be dry, solid, clean and free of grease and dust. Brush out untreated, rough-sawn wood beforehand and prime with LEINOS Impregnation Primer 150. Scrape out resin spots and clean with LEINOS Thinner 200. Resin build-up cannot be prevented by coating measures. How to apply Apply sparingly by brushing, rolling or spraying at an ambient and surface temperature above 15°C. Two coats required. Product is ready to use. Stir carefully before use! Sprayability: Non-binding guide values: Airless: Nozzles 0.23-0.33 mm, spray angle: approx. 30°, filter approx. 180 meshes. Drying time At 20 °C and 50 % relative humidity: Dust-dry after approx. 12 hours. Dry and recoatable after approx. 24 hours. This system requires sufficient quantities of atmospheric oxygen for drying. Coverage Approx. 55-85 ml/m² per coat on planed or sanded wood. The consumption is slightly higher for rough sawn wood. Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Shelf life is at least 2 years if unopened. Close opened containers tightly, decant leftovers into smaller containers. Carefully remove any skin formation in the can before use and do not stir in. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 290 g/l, EU limit value: 300 g/l (cat. d). EAK: 08 01 11 / GISCODE: BSL10 Hazard statements Repeated exposure may cause skin dryness or cracking. Contains 3-Iodo-2-propynyl-butylcarbamate. May produce an allergic reaction. Active ingredient: 3-Iodo-2-propynyl-butylcarbamate <0,6%. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Solvent-free, matt coating for all untreated exterior wooden structures. Well suited for rough sawn wood. Not suitable for oak wood! Technical properties Good hiding power. Permeable to water vapour. Easy to renovate. With film protection against fungal attack. Colour 014 Mashed yellow, 057 Swedish red Ingredients Water, linseed oil, rye flour, bentonite, ferrous sulphate, iron oxide pigments, potassium oleate, iodopropynyl butyl carbamate, drying agents. Substrate and preparation The substrate must be dry, solid, clean, free of grease and dust and must not be absorbent. Brush out untreated, rough-sawn wood beforehand. How to apply The substrate must be dry, solid, absorbent, clean and free of resin and dust. Apply by brushing at an ambient and surface temperature above 10 °C. Product is ready to use. Stir carefully before use! Drying time At 20 °C and 50 % relative humidity: dust-dry after approx. 2 hours. Dry and recoatable after approx. 24 hours. Coverage Approx. 55-85 ml/m² per coat on planed or sanded wood. The consumption is slightly higher for rough sawn wood. Apply sparingly to avoid drying problems! Thinner and cleaning agent Thinner with up to 20 % water. For cleaning, use water and LEINOS Intensive Cleaner 935 or LEINOS Thinner 200 for stubborn stains. Storage and shelf life Store in a cool and dry place. Shelf life is at least 2 years if unopened. Close opened containers tightly, decant leftovers into smaller containers. Special notes Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 / GISCODE: BSW50 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one; 1,2-benzisothiazolin-3-one. May cause allergic reactions. Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Off-porous topcoat for interior use on wood, metal and neutral stone. Suitable for dimensionally stable wooden components such as windows and doors. White Lacquer can be used for radiators as well as floor surfaces such as wooden stairs or floors. Cannot be used on aluminium and galvanised surfaces. Technical properties Water-resistant, elastic White Lacquer with good hardness and high hiding power. Good flow, high coverage, low yellowing. Water vapour permeable. Colour Natural white. 031 Silk gloss. Ingredients Binder based on vegetable oil, aliphatic hydrocarbons, titanium dioxide, mineral fillers, additives, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, free of grease and dust and must not be absorbent. How to apply Product is ready to use. Stir carefully before use! Brushing, rolling or spraying. Room and surface temperature above 15 °C. Check compatibility and adhesion with the substrate by creating test surfaces. Lightly sand (P180) between priming and intermediate coats after drying. Wear a dust mask when sanding! If necessary, a second coat of White Lacquer can be applied. The final gloss level is achieved 2-3 weeks after application. A. Coating structure on untreated or absorbent substrates: Prime absorbent substrates with LEINOS Primer Oil 220, in damp areas with LEINOS Impregnation Primer 150. Alternatively, apply 1 coat of LEINOS Resin Lacquer Primer 810. After drying, apply 1-2 coats of White Lacquer 820. B. Renovation coat on existing old coat: Sand and remove dust. Then apply 1-2 top coats of White Lacquer 820, with primer if the substrate is absorbent. C. Renovation coat on heavily damaged old coat: Completely remove any loose paint, then sand. Further coat build-up as under A, with primer if the substrate is absorbent. Sprayability (non-binding guide values): Airless: Working pressure 120 - 160 bar, fine surfaces (cabinets, mouldings, furniture): Nozzle 0.28 - 0.33 mm, General painting work (doors, walls, ceilings): Nozzle 0.33 - 0.38 mm, gun filter 200 mesh. High pressure: Working pressure 2.0 - 2.5 bar, nozzle approx. 0.28 - 0.33 mm. Low pressure: Working pressure 0.2 - 0.8 bar, nozzle size: for paint colours 1.6 - 1.8 mm. Drying time Dust-dry after approx. 8-10 hours, dry and paintable after approx. 24 hours, completely dry after approx. 3-6 days. This system requires sufficient quantities of atmospheric oxygen for drying. For reliable drying and to avoid odours, we always recommend using a fan to ensure sufficient air circulation on the surface of the paint during the drying phase. Coverage Approx. 70-100 ml/m² per coat. Apply sparingly to avoid drying problems! Thinner and cleaning agent Product is ready to use. Clean tools immediately after use with LEINOS Thinner 200. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Carefully remove any skin formation in the can before processing and do not stir in. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 295 g/l, EU limit value: 300 g/l (cat. d). EAK: 08 01 11 / GISCODE: BSL10 Hazard statements Harmful to aquatic life with long lasting effects. Repeated exposure may cause skin dryness or cracking. Contains cobalt octoate. May cause allergic reactions. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)