Preparation
Application For priming highly or differently absorbent substrates before further treatment with LEINOS wall paints: 640 Casein Wall Paint 650 White Emulsion Paint 655 Clay Paint 656 Clay Mix 657 Clay Plaster Mediterranean 658 Clay Plaster Fine 660 Natural Resin Emulsion Paint 670 Natural Mix 680 Plaster-Effect Paint Mediterranean 685 Plaster-Effect Paint Fine Technical properties Transparent primer. Very high vapour permeability. Colour Almost colourless after drying. Ingredients Water, shellac soap, natural resin soap, carnauba wax, beeswax, cellulose, potash, benzisothiazolinone. Substrate and preparation Suitable substrates are neutral plasters, porous stone, plasterboard and old, firmly adhering coats of wall paint. The substrate must be dry, clean and free of dust and grease. How to apply Brushing, rolling, spraying. Ambient and surface temperature above 15°C. As a primer, the product must be diluted 1:1 with water. Note: To achieve the full load-bearing capacity of the final coat, the substrate must still be moderately absorbent when applying the final coat. Drying time 2 - 4 hrs. Coverage Approx. 60-100 ml/m² when diluted, depending on the absorbency of the substrate. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930. Storage and shelf life Stable for approx. 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost. Special notes EAK: 07 06 01 Hazard statements Contains 1,2-benzisothiazol-3(2H)-one. May produce an allergic reaction. Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Hotline for allergy sufferers: +49 4163 / 867 47-0 Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For smoothing interior wall and ceiling surfaces and for filling joints in plasterboard and other building boards. Colour White, matt. Ready-mixed, tintable with LEINOS Water-based Pigment Concentrate 668, see Technical Data Sheet 668. Ingredients Finely ground calcium sulphate (natural gypsum), calcium carbonate and methyl cellulose. Substrate and preparation Can be used on stone, plaster, concrete, aerated concrete, insulating panels, etc. The substrate must be clean, solid, dry and sound. Dust, dirt, wallpaper, non-adherent or weakly bonded paints and loose, non-load-bearing plasters must be removed. Mixing ratio: Mix 1 kg of Interior Smoothing and Texturing Filler with 600 ml of water. Stir again briefly after 2-3 minutes. How to apply To fill holes and cracks, press Interior Smoothing and Texturing Filler 684 firmly into the cavity and level off. For smooth surfaces, re-fill if necessary or wet and smooth evenly with a sponge board. Further work, e.g. sanding, wallpapering, painting, can be carried out after complete drying. When laying plasterboard or wall panels, apply Interior Smoothing and Texturing Filler 684 in dots to the back of the panel, press on and align the panel. Processing temperature: At least +5 °C for substrate and room air temperature. Coverage Depending on application thickness. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930. Special notes When jointing plasterboard panels, there is no need to insert reinforcement strips if the panels are shaped accordingly. GISCODE: CP1 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Inside. Technical properties High-quality, organic lime putty for filling holes and smoothing walls. Can also be used for decorative wall design. Its moisture-regulating properties, in conjunction with the high pH value (approx. 13), make it ideal for use in mould remediation. Ingredients Marble powder, limestone powder, hydrated white lime, hydrated lime, methyl cellulose, vegetable polysaccharide. Polysaccharide. Substrate and preparation All substrates must be pre-treated in accordance with the specifications of VOB/C DIN 18363. Mineral substrates as well as gypsum fibreboards and firmly adhering old coatings are suitable for processing. Before levelling, we generally recommend an adhesion-promoting and absorbency-regulating primer coat with LEINOS Silicate Primer 621 or Mineral Plaster Primer 622. How to apply mix 20 kg of LEINOS Lime universal scraper thoroughly and lump-free with approx. 6 litres of clean water. Apply within 5 hours with a plastering board or smoothing trowel in layer thicknesses of 1 - 3 mm. The surface is felted or smoothed. Do not apply at temperatures below 5°C and allow to dry. LEINOS Lime Filler can be recoated with LEINOS Lime Paint and Silicate Paint products. IMPORTANT: Ensure alkali-resistant substrates and products! Carefully cover and protect eyes, skin and alkali-sensitive substrates. Drying time Depending on layer thickness, but at least 24 hours. Very slow drying from 3 mm layer thickness. Carbonation time: at least 2-3 days. Coverage Consumption per mm application thickness/m² approx. 1 kg. Thinner and cleaning agent Cleaning with water. Storage and shelf life Protect from moisture. Store dry and tightly closed. can be stored for 12 months. Special notes Always create a test area of at least two square metres to check the adhesion behaviour. The test area must be thoroughly dry before a definitive assessment of adhesion and cracking behaviour can be made. Do not leave the material wet but in a bucket to dry out and dispose of with household waste. With their special properties, LEINOS lime paint products are in keeping with a very old paint tradition and are becoming increasingly popular, particularly in the area of mould remediation, due to their high pH value and diffusion properties. A slight cloud formation, glossy lime sinter layers and colour variations on the wall surface correspond to the typical appearance of a lime paint coat. This appearance is influenced by the substrate, temperature and humidity and is one of the natural properties. The ageing of lime coatings is caused by a continuous, very slow reduction in coating thickness and is referred to as chalking in the technical literature. This chalking is a typical property of the material and NOT a product defect. Hazard statements Causes skin irritation. Contains: calcium hydroxide; natural hydraulic lime. Causes serious eye damage. Safety instructions Wear protective gloves/protective clothing/eye protection/face protection. IF ON SKIN: Wash with plenty of water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF INHALED: Remove person to fresh air and keep comfortable for breathing. Use only outdoors or in a well-ventilated area. Avoid breathing spray mist. Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For LEINOS Silicate and Lime Paints, e.g. on lime plaster, cement plaster, sand-lime brick, cement, aerated concrete, brick, concrete, clay brick, clay plaster, Fermacell, plasterboard, well-adhering old emulsion paint coats, etc. Technical properties Solvent-free and water vapour permeable. Produces a sand-rough surface for subsequent coating with silicate or lime paints. pH value approx. 11. Grain size approx. 0.04 mm. Colour Natural white, matt. Ingredients Water, potassium water glass, cellulose ether, chalk, marble powder, acrylate dispersion. Substrate and preparation The substrate must be dry, solid, absorbent, clean and dust-free. Treat slightly chalky but still stable substrates once generously with LEINOS Silicate Primer 621. Completely remove old, glossy latex, oil and varnish paints or treat with LEINOS Leaching Cleaner 950. If in doubt, apply a test coat. How to apply Brush or roll on the product undiluted or diluted up to max. 10 % with clean water. Always stir well before use and during application. Drying time At 20 °C and 50 % relative humidity: approx. 6-12 hours. Subsequent coats after 24 hours drying time. Coverage 1 litre is sufficient for approx. 5 m², depending on the structure and absorbency of the substrate. Thinner and cleaning agent Water and LEINOS Vegetable Soap 930, product is ready to use. Storage and shelf life Store in a cool, dry and frost-free place. Stable for approx. 12 months when originally sealed. Special notes All LEINOS Silicate Paint products are particularly suitable for historical buildings, but also for use in modern architecture. In contrast to conventional paints bound with synthetic resins, silicate paints do not form a paint film after drying, but a paint layer. The ageing of these silicate paints is characterised by a continuous, very slow reduction in coating thickness. In technical literature, this behaviour is referred to as "chalking". This chalking is a typical property of the material and NOT a product defect. To achieve optimum results, the material must be thoroughly stirred and sieved before use so that dried colour particles are removed from the edge of the bucket or lid. These are typical properties of the material and NOT a product defect VOC content: <1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 20 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Do not get in eyes, on skin, or on clothing. Caution! Product is alkaline! Protect eyes and skin against splashes. Splashes on glass, natural stone, aluminium, wood and paint should be washed off immediately with plenty of water. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For substrate pre-treatment of subsequent silicate and lime paint coats. Technical properties Special, very highly water vapour permeable deep primer. Anti-fungal and mould-inhibiting, pH value approx. 11. Colour Almost colourless after drying. Ingredients Water, potassium water glass, organic binders. Substrate and preparation Depending on the strength and absorbency of the substrate, the product must be diluted with water up to a ratio of 1:3. ATTENTION: "Glazing" of the substrate must be avoided at all costs! How to apply Paint at an ambient and surface temperature above 15 °C. Carefully cover and protect eyes, skin and alkali-sensitive surfaces. Drying time At 20 °C and 50 % relative humidity approx. 1-3 hours. Coverage Approx. 100 ml/m² (thinned), depending on the absorbency of the substrate. Thinner and cleaning agent Cleaning with water. Storage and shelf life Stable for at least 12 months when originally sealed. Store in a cool, dry and sealed place. Protect from frost! Special notes VOC content: 1 g/l, EU limit value: 30 g/l (cat. a). EAK: 08 01 03 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Do not get in eyes, on skin, or on clothing. Caution! Product is alkaline! Protect eyes and skin against splashes. Splashes on glass, natural stone, aluminium, wood and paint should be washed off immediately with plenty of water. Technical data sheet (PDF) · Safety data sheet (PDF, in German)