Solvent-free oils for indoors
Application For treating wooden kitchen worktops, furniture surfaces and children’s toys. Technical properties An oil-wax mixture, solvent-free, which permanently enhances the wood and guarantees a durable surface. Impregnating, water-repellent, open-pored, vapour-permeable. Saliva- and sweat-resistant in accordance with DIN 53 160. Tested in accordance with DIN EN 71, Part 3. When used as intended, the product complies with Regulation (EC) No 1935/2004 and the German Food, Consumer Goods and Animal Feed Code (LFGB). Ingredients Linseed oil, wood oil, sunflower oil, safflower oil, walnut oil, fatty acid methyl esters, kaolin, clay, drying agents. How to apply The substrate must be dry (wood moisture content max. 14 per cent), solid, absorbent, clean, and free from resin and dust. Finish sanding well with 240-grit sandpaper. Stir thoroughly before use. Apply with a brush, sponge, lint-free cloth or roller, and spread thoroughly. Drying time The drying time depends on the environment. At 20–23 °C, the drying time is 12–24 hours, depending on the amount of oil applied. To ensure the paint dries properly and to prevent odours from developing, we always recommend using a fan to ensure adequate air circulation over the painted surface during the drying phase. Coverage Approx. 60–80 ml/m² per coat. Apply sparingly to prevent drying problems! Storage and shelf life Store in a cool, dry place. Unopened, it will keep for at least 2 years. Seal opened containers tightly and transfer any remaining product to smaller containers. Special notes Store work materials impregnated with the product, where the oil has not fully dried, in an airtight metal container or in water, and then dispose of them, as there is otherwise a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may cause a characteristic odour. When using spray equipment, wear approved respiratory protection. Wear a fine dust mask when sanding! VOC content: 10 g/l. EU limit value: 400 g/l (Cat. e). EAK: 08 01 12 / GISCODE: BSL10 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application Indoors. For open-pored impregnation of wood. Creates a hard-wearing surface. Technical properties Scratch-resistant, water-repellent impregnation. Water vapour permeable. Solvent-free. Tested for migration behaviour in accordance with DIN EN 71, Part 3. Colour Colourless to slightly yellowish. Ingredients Linseed oil, wood oil, ricin oil, sunflower oil, carnauba wax, clay, drying agents. Substrate and preparation To achieve optimum results, please observe the technical data sheets for all products used. The substrate must be dry, solid, clean, free of grease and dust and absorbent. Pre-sand wooden surfaces with 100-150 grit in the direction of the grain. How to apply Apply once with a thermopad or polishing machine or surface brush. Room and surface temperature above 15 °C. A. Coating build-up on untreated or absorbent substrates: For hot application: Deep impregnation with a single application. In the floor area, apply a thin coat of cold Hard Oil Solvent-free 248 with a flat brush. Then carefully work in hot with a Thermopad machine. For cold application: Apply Hard Oil Solvent-free 248 1-2 times with an intermediate drying time of 24 hours. In floor areas, apply the product thinly with a flat brush. Then work in carefully with a polishing machine and white pad. If necessary, apply a second coat after an intermediate drying time of 24 hours. Consumption here only 3-5 g/m². Apply Hard Oil LF 248 drop by drop and polish in with a white pad. In general: Before further treatment with a LEINOS wax product, it must be ensured that the primed substrate is well dried and no longer absorbent in order to avoid impoverishment of the subsequent films and thus inferior surfaces! B. Renovation coat: Clean and sand the substrate. Then apply Hard Oil Solvent-free 248 once. Waxed surfaces can be renovated with Hard Oil Solvent-free 248 if the wax has been completely removed beforehand. Drying time Dust-dry after 24 hours. Dry after 48 hours. In general: This system requires sufficient oxygen in the air for drying. Therefore, ensure good ventilation, e.g. with a fan in stagnant air, to avoid odours. Coverage Consumption per application: Surface brush 20-30 ml/m². Apply sparingly to avoid drying problems! Thinner and cleaning agent LEINOS Thinner 200 is a ready-to-use product. Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: <10 g/l, EU limit value: 400 g/l (cat. e). GISCODE: Ö 10+ / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions If medical advice is needed, have product container or label at hand. Keep out of reach of children. Read carefully and follow all instructions. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For priming and finishing all absorbent substrates, such as wood and cork floors, terracotta, stoneware tiles, neutral screed floors, wood-based panels such as Sterling OSB boards, etc., indoors. Technical properties Hardwax Oil LF is an oil-wax mixture, solvent-free. It gives the wood a durable finish and guarantees a hard-wearing surface. It revitalises the wood structure and gives it a velvety sheen. Tested for migration behaviour in accordance with DIN EN 71, Part 3 and tested for saliva and perspiration fastness in accordance with DIN 53160. Colour 002 Colourless, 202 White. Ingredients Wood oil, linseed oil, ricin oil, sunflower oil, clay, kaolin, micro wax, mineral pigments (except colourless), drying agents. Substrate and preparation The substrate must be dry (wood moisture content max. 14 %), clean and dust-free. The application temperature should preferably not be below 16 °C. Drying behaviour is delayed at lower temperatures. Final sanding of the surfaces with at least 120 grit or grid. How to apply Apply Hardwax Oil LF evenly once with a double-sided trowel (approx. 15-30 ml/m², depending on the absorbency of the wood). Then pad thoroughly with a single disc polishing machine and green pad and polish the surface with a white pad. After 12 hours, apply a second thin coat of Hardwax Oil Colourless LF 291 or Hardwax Oil Colourless 290. For heavily used or particularly absorbent floors, apply a second coat sparingly the next day. Pad the surface with a white pad after 20-30 minutes. Ensure optimum fresh air circulation when applying and drying the products! Otherwise unpleasant odours are possible! Avoid layer formation at all costs! Please note: Floors must be laid without joints or levelled if necessary. If joints are present, oil may leak or noise may be generated when walking on the floor. Drying time The drying time is approx. 6-12 hours (20-23 °C / 50-55 % relative humidity). Complete drying and full load-bearing capacity after 7-10 days. For reliable drying and to avoid odours, we always recommend the use of a fan to ensure sufficient air circulation on the surface during the drying phase. Coverage 15-30 ml/m²; coverage: approx. 30-60 m²/l depending on the substrate. Thinner and cleaning agent LEINOS Thinner 200. Storage and shelf life Store in a cool and dry place. Close container tightly. Stable for at least 2 years when originally sealed. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! Colour specifications and colour imprints are non-binding. Colour deviations are possible depending on the batch, substrate and printing technique. The dried original colour shade differs from the fresh colour shade in the container. A test coat with colour matching is therefore essential. Mix different batches of the same colour shade together. VOC content: 1 g/l, EU limit value: 700 g/l (cat. f). EAK: 08 01 11 / GISCODE: Ö 10+ Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)
Application For one-time application on all interior wood. Not suitable for kitchen worktops, stairs and floors. Technical properties Solvent-free, impregnating, layer-forming. Elastic, antistatic. Welding and saliva resistant according to DIN 53 160. Colour Colourless, transparent. Ingredients Safflower oil, sunflower oil, linseed oil, wood oil, ricin oil, natural resin ester, beeswax, carnauba wax, micro wax, drying agents. Substrate and preparation The substrate must be dry, firm, clean and free of grease and dust. Shake well before use. How to apply Apply cold or hot with a brush, at room air temperatures above 15 °C. Allow to soak in, polish in with a pad after a contact time of 1-24 hours. Intermediate drying is not possible as there is no surface dryer. Drying time At 23 °C and 50 % relative humidity 24 hours. The supply of warm air considerably shortens the drying time. Coverage 1. Apply 10-15 ml/m², considerably less or more depending on the absorbency and surface condition of the substrate. Stir well. Carry out a test coat! Storage and shelf life Stable for at least 2 years when originally sealed. Store in a cool, dry and sealed place. Special notes Work materials soaked in product with oil that is not completely dry should be stored in an airtight metal container/water and then disposed of, otherwise there is a risk of spontaneous combustion due to the vegetable oil content. The natural raw materials used may give off a typical odour. Wear approved respiratory protection when using spraying equipment. Wear a fine dust mask when sanding! VOC content: 1 g/l, EU limit value: 400 g/l (cat. e). GISCODE: BSL10 / EAK: 08 01 11 Hazard statements Safety data sheet available on request. Safety instructions Keep out of reach of children. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. Do NOT induce vomiting. Avoid release to the environment. Dispose of contents/container to an appropriate recycling or disposal facility. Technical data sheet (PDF) · Safety data sheet (PDF, in German)